7894

Rebox RE-2250MG Manual

39
Zoom out
Zoom in
Previous page
1/47
Next page
www.rebox.tv
39
• Power on Channel: This function allows you to set the channel you want when the receiver turns on. To
set the power on channel, apply the following steps (Figure 18):
1. Select Power on Channel and press OK or the Right button.
• Last Channel: The receiver will start-up with the channel that you viewed before turning the
receiver off.
• Defined Channel: This function allows you to set the channel you want when the receiver
turns on. To define the channel, apply the following steps:
1. Press OK or the Right button and select in the TV or radio list of channels the channel you
want to have your receiver start-up with.
• Software Upgrade: You can download the latest software available including new technologies to your
receiver. To upgrade your system, apply the following steps:
1. Select “Software Upgrade” and press OK. Enter your PIN code.
2. Press the Green button to scan the satellite for availability of a newer software version. If
there is a recent software version available for your receiver, it will be detected.
3. Press the Red button to start the upgrade.
4. Press the BACK button until you go back to main menu.
Note: Be sure that your receiver is connected to the satellite signal. Do not turn off your receiver while you
are downloading new software.
System Info: The system information displays information about your receiver such as model
number,software and boot version. To check system information, apply the following steps:
1. Select “System information” and press OK. Press Back to return to the menu
Mediaguard: Here you will find information about the embedded Mediaguard decoder.
Select “Mediaguard” and press OK. Press Back to return to the menu (Figure 20)
Factory Reset: Be careful when using this function, because it will erase all the data and parameters you
may have set earlier to your receiver. Once you have made a Factory Reset you will have to re-install
your preferences and re-scan your channels. To reset your receiver to factory default, apply the
following steps:
Select “Factory Reset” and press OK.
Enter your PIN Code. The receiver will reset itself to the original factory settings.
Note: Your PIN code will change back to the factory setting “0000”.
5.1.4.2 LNB Set-up
It is recommended that you read the manual and installation instructions of your LNB, your DiSEqC switch, your
0/12V switch and your Positioner before you start setting up your LNB. To set up your LNB, please apply the
following steps:
1. Press the Menu button.
2. Using UP/DOWN keys, select "Installation" and press OK.
3. Using UP/DOWN keys, select "LNB Set-up" and press OK (Figure 22)
4. Check the exact specifications of your LNB through the manufacturers informationor your dealer.
There are up to 16 types of LNB's available. The Default is set to Universal mode
(9750/10600MHz), DiSEqC is not used and the LNB is mounted on a fixed dish.
5. Use the UP/DOWN keys on your remote to select an item and use the LEFT/RIGHT buttons to set
up any values.
• LNB: Up to 16 LNBs are available, select and set-up the correct one according to your LNB
specifications. Press OK on the LNB number that you want to set-up.
• LNB Type: Select the LNB type from Universal 1 ~ 3, and Single. You should type the LNB
value in Single. In Single, the item parameter is 0 or another number. In UNI1=9750/10600
MHz, UNI2=9750/10700 MHz, UNI3=9750/10750 MHz.
• LNB Power: Select 13/18V, 13V or 18V for LNB. Select “Off” if you want to switch the power
of the LNB off.
… 39 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rebox RE-2250MG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rebox RE-2250MG in the language / languages: Dutch as an attachment in your email.

The manual is 0,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info