623533
21
Zoom out
Zoom in
Previous page
1/28
Next page
19
ArtNo.800-0126 - Fitting the sealing strip
This dishwasher is for use in GB and IE only. After sales service
applies to GB and IE only.
Positioning the Dishwasher

Do not install the dishwasher in a room where the
temperature is likely to fall below freezing (0 °C).

Do not grip the door when moving the dishwasher.
The dishwasher should be aligned to the front of the adjacent
cabinets, with allowance made for the door thickness. The
dishwasher has water supply and drain hoses that can be
positioned on either to the left or the right.
Before installing the dishwasher into a kitchen cabinet,
holes must not be drilled into the sides, or door, to avoid
compromising the performance and operation of the
dishwasher.
A plastic self-adhesive anti-condensation strip is supplied
with the dishwasher. Fix the strip to the underside of the
worktop, along the front edge (Fig.5-1).
Connect up the cold water supply, the drain hose and the
electrical connections (see below) then slide the dishwasher
into the cabinet opening.
Cold Water Connection
Connect the water supply hose (supplied loose) to the cold
water inlet at the rear. Connect the other end to a ¾“ BSP tap
connector (Fig.5-2). Make sure that the washers are in place
and that it is fastened securely in place.
IMPORTANT: If the water pipes are new or have not been
used for an extended period of time, run the water for
a while to make sure that the water is clear and free of
impurities BEFORE connecting to the dishwasher. Failure
to carry out this precaution may lead to the water inlet
becoming blocked and causing damage the dishwasher.
The water prssure should be between 0.03 Mpa and 1Mpa.
Pressures above 1Mpa will require a pressure relief valve to
be tted.
Drain Hose Connection
Connect the drain hose to the water outlet. Insert the hose
into a drainpipe with a minimum diameter of 40 mm, or let it
run into a sink, making sure to avoid bending or crimping. If
necessary, t a siphon trap (U-bend) with a connecting piece.
The free end of the hose must be at a height of between
50 -110 cm and must not be immersed in water (Fig.5-3).

WARNING! The connecting piece for the siphon trap
(U-bend) must be solidly fastened to the wall to
prevent the drain hose from moving and allowing
water to spill outside the drain (Fig.5-4).
ArtNo.800-0101 - Cold water connection
Washer
Water hose
¾“ BSP tap connector
110cm
50cm
Fig.5-1
Fig.5-2
Fig.5-3
Waste
hose
Waste hose support
(xed to wall)
To waste
Fig.5-4
5. Installation
• DocNo.800-0503 - Installation - RDW459 dishwasher
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rangemaster RDW1045FI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rangemaster RDW1045FI in the language / languages: English as an attachment in your email.

The manual is 1,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info