713897
13
Zoom out
Zoom in
Previous page
1/120
Next page
FOLDING BACK– Zero Offset (Fig. A)
1. Remove screw (2), nut (3), eccentric washer (4) and offset plastic
saddle (5) from backplate / back rest assembly.
2. Aluminum– Swap the 1-3/4" long screw (2) for a 1-7/8" long screw
(2A) and the "offset" plastic saddle (5) (with the step in it) for a plas-
tic saddle (5A) without offset (no step).
Titanium– Swap the 1-7/8" long screw (2) for a 2" long screw (2A)
and the "offset" plastic saddle (5) (with the step in it) for a plastic
saddle (5A) without offset (no step).
3. Holding plastic saddle (5A) against backrest tube, slide the sideguard
(6) and plastic washer (7) between the backplate (1) and the plastic
saddle(5A), as shown in Fig. A.
4. Choose the side guard height by aligning one of the holes in the side
guard, with the holes in the backplate (1), plastic washer (7), plastic
saddle (5A) and backrest tube.
5. Insert screw (2A) through the eccentric washer (4), backplate (1),
plastic washer (7), side guard (6), plastic saddle (5A) and backrest
tube. Attach nut (3).
6. Align slot in side guard with hole in seat frame.
7. Insert 1-7/8" long screw (8) through side guard bushing (9), plastic
washer (7), sideguard slot, 2nd plastic washer (7), plastic saddle
(5A), and seat frame. Attach nut (3A).
8. Secure screws (2A & 8) and nuts (3 & 3A).
9. Repeat procedure for opposite side.
10. Check backrest folding - if necessary, adjust tension in screw (8) and
nut (3A) to achieve proper folding function.
930494 Rev. A
13
ENGLISH
E. SIDE GU
ARD INSTALLATION
Your Match Point has been assembled with either a "Folding" or "Fixed" backrest. Determine the configu-
ration of your chair and follow the appropriate installation instructions. Two mounting options are avail-
able for your side guards:
1. Zero Offset
The side guard width is the same as the seat frame width. The side guards mount inside the backplate.
2. 1/4" Offset
Seat frame width will be 1/2" wider with side guards (1/4" per side). The side guards mount outside the
backplate.
FOLDING BACK– 1/4" Offset (Fig. B)
1. Remove screw (2), nut (3) and eccentric washer (4) from backplate /
backrest assembly.
2. Aluminum– Swap the 1-3/4" long screw (2) for a 2" long screw
(2A).
Titanium– Swap the 1-7/8" long screw (2) for a 2" long screw (2A).
3. Choose the side guard height by aligning one of the holes in the side
guard, with the holes in the backplate (1), plastic washer (7), plastic
saddle (5) and backrest tube.
4. Insert 2" long screw (2A) through the side guard (6), plastic washer
(7), eccentric washer (4), backplate (1), plastic saddle (5) and back-
rest tube. Attach nut (3).
5. Align slot in side guard with hole in seat frame.
6. Insert a 2" long screw (2B) through side guard bushing (9), plastic
washer (7), sideguard slot, plastic washer (7), plastic saddle offset (5)
and seat frame. Attach nut (3A).
7. Secure screws (2A & 2B) and nuts (3 & 3A).
8. Repeat procedure for opposite side.
9. Check backrest folding - if necessary, adjust tension in screw (2B)
and nut (3A) to achieve proper folding function.
Figure A – Folding Back, Zero Offset
Figure B – Folding Back, 1/4" Offset
Backrest
Tube
Seat
F
rame
Backrest
Tube
Seat
Frame
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quickie Match Point Ti at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quickie Match Point Ti in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info