713897

Quickie Match Point Ti Manual

15
Zoom out
Zoom in
Previous page
1/120
Next page
930494 Rev. A
15
ENGLISH
F
. SEAT SLING
The seat sling can be adjusted through the use of VELCRO® style retaining material beneath the seat.
Adjustment
a. Remove the screws retaining the left side seat sling.
b. Readjust VELCRO® style material to adjust the tension in the seat sling.
c. Replace screws and torque to 45 inch-lbs (5 N-m).
d. If there is any difficulty in reattaching the screws, try using a probe to help line up the holes.
G. CUSHION (OPTIONAL)
Installation
a. Place cushion on seat sling with VELCRO® side down. The beveled edge of the cushion should
be in front.
b. Press firmly into place.
H. REAR AXLE ASSEMBLY
1. Center of Gravity Adjustment
The most important adjustment on your Quickie Match Point is the position of your center of gravity.
The position of your seat frame will determine your center of gravity.
• The further forward the seat, the more stable the chair becomes.
• Moving the seat frame back will increase your turning speed and lighten the front end.
For example: Using hole 1 will increase your turning speed.
Using hole 8 will give you a more stable ride.
2. Wheel Camber
Increasing wheel camber angle provides greater side-to-side stability due to the increased width and
angle of the wheelbase and also allows for quicker turning and greater access to the top of the handrims.
The wheel camber option from the factory is 16° & 20°.
3. Rear Wheel Axle Sleeve Adjustment
Tight axle sleeves (1) should be maintained for proper performance of the wheelchair.
a. To adjust axle sleeve, you will need a 1 1/8" open end wrench to turn the outside axle sleeve nuts
(2).
b. You will also need a 5/8" wrench to hold the axle sleeve in place while loosening or tightening
the axle sleeve nuts.
c. Loosen nuts and adjust axle sleeve in or out to desired location. Distance should be equal on
both axle sleeves.
d. Hold axle sleeve with 5/8" wrench and tighten nuts.
4. Toe-in and Toe-out
T
oe-in and T
oe-
out are terms that relate to how well the rear wheels of the chair are aligned. This will
affect how well the chair will roll. Drag or resistance occurs in a wheelchair when the rear wheels are
not properly aligned.
Toe-in or toe-out can be adjusted by loosening the axle-sleeve nut and then slightly rotating the axle
sleeve forwards or backwards.
a. Toe-in: To eliminate toe-in, rotate the top of the axle-sleeve toward the rear of the chair.
b. Toe-out: to eliminate toe-out, rotate the top of the axle-sleeve toward the front of the chair.
To check that the rear wheels are properly aligned, measure the centerline to centerline of the tires at
the midpoint front and rear until the desired measurement is achieved.
(Detail)
1
4
8
Camber Tube
16° & 20°
Eccentric Axle Sleeve
1
2
Toe-out
Toe-in
A
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quickie Match Point Ti at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quickie Match Point Ti in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info