713897

Quickie Match Point Ti Manual

12
Zoom out
Zoom in
Previous page
1/120
Next page
930494 Rev. A
12
ENGLISH
IX. SET-UP AND ADJUSTMENT
A. SET
-UP
Setting the wheelchair on a table or flat surface, such as a workbench or table, helps make these pro-
cedures easier.
Torque Settings: A torque setting is the optimum tightening which should be made on a particular
fastener
. A torque wrench which measures in./lbs. should be used when tightening fasteners on
Quickie wheelchairs. Unless otherwise noted, use a torque setting of 60 in./lbs. when setting up this
wheelchair.
B. TO MOUNT & REMOVE REAR WHEELS
WARNING
Do not use this chair UNLESS you are sure both quick-release axles are locked.
An unlocked axle may come off during use and cause a fall.
NOTE: Axle is not locked until the quick-release button pops out fully. (Fig. A)
1. To Install Wheel
a. Depress quick-release button (1) fully. This will release tension on ball bearings at other end.
b. Insert axle through hub of rear wheel.
c. Keep pressure on button (1) as you slide axle (2) into axle sleeve (3).
d. Release button to lock axle in sleeve. Adjust axle if it does not lock. (See Section C)
e. Repeat steps on other side.
2. To Remove Wheel
a. Depress quick-release button (1) fully.
b. Remove wheel by sliding axle out of axle sleeve.
c. Repeat steps on other side.
C. AXLE ADJUSTMENT
1. To adjust the axle you will need a 3/4" wrench to turn the outside axle nuts.
2. You will also need a 1/2" wrench to lodge the ball bearings, on the opposite end of the axle,
and prevent the axle from turning.
3. Turn the outside axle nut counterclockwise to tighten.
4. There should only be zero to ten thousandths of an inch (.010) of play.
D. BACKREST (FIXED OR FOLDING)
1. Backrest Installation
To install backrest, remove the nut, plastic saddle and bolt from the backrest tube. Place the backrest
in the upright position and reinstall in the lower plate hole (A). Backrest bolts should be tightened to
65 in-lbs. (7.3 Nm). Avoid over-tightening as you may crush the backrest tubing.
2. Back Angle Adjustment
Back angle adjustment is standard on all Quickie wheelchairs.
a. Loosen bolt and nut on both sides of wheelchair.
b.
Turn the eccentric washer (B) on the backrest hinge plate to increase or decrease the back
angle.
c. Tighten bolts and nuts.
d.
The adjustment on each side of the chair must be exactly equal.
3. Height Adjustment (Aluminum only) (Excluding 9" back)
The backrest comes standard with a 3" height adjustment.
1.
R
emove the backrest upholstery from the frame.
2. You will see the backrest tube (C) which telescopes into the back frame and is secured by a
pushbutton (D) on the side of the backrest.
3.
There are several holes, 1" apart in the back frame (E), from which you may choose to set the
back height.
4. Depress the pushbutton and move the backrest tube to the desired hole location.
5. Assure that the pushbutton fully engages into the back frame.
6. Slide the backrest upholstery back onto the back frame.
7. Secure the VELCRO® style material to the back frame.
1. Quick-release
2
3
Figure A
A
B
D
E
C
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quickie Match Point Ti at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quickie Match Point Ti in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info