815530
23
Zoom out
Zoom in
Previous page
1/30
Next page
23 10/238106-804K
Following correction of any Alarm, turn the dial control to the OFF position, wait 10 seconds and turn back to
desired setting OR unplug the appliance, wait 10 seconds then restore power.
Alarm
(LED Flashing RED) Possible Cause Corrective Action
1RedFlash:EmptyHopperAlarm
Hopper empty Fill the hopper
Auger jam Inspectthefeedtubeforjams
Vacuum switch not closing
Makesurereboxdoorisshut,vacuum
hose is connected to switch and drop
tube, wire connectors are connected to
vacuum switch, control board, hopper
switch, and safety snap disc.
Hopper lid open Close the hopper lid
Exhaust probe does not sense
temperature
Secure the exhaust probe keeping its
wire away from hot surfaces and clean
the exhaust plenum
Snap disc tripped (#3) Reset snap disc
Exhaust probe not attached to outlet
Inspect the exhaust probe to see if it
is securely attached to the side of the
exhaust outlet - keeping its wire away
from hot surfaces
Exhaust path is dirty Clean appliance including the re pot,
exhaust path, and venting system
2RedFlashes:ExhaustProbeFail
Not connected to the control board Connect terminal end to control board
Failed component
Replaceexhaustprobe–securingitto
exhaustblowerhousing–keepingwire
away from hot surfaces
4RedFlashes:MissedIgnition
Hopper empty Fill the hopper
Feed motor doesn’t turn
Inspect feed motor circuit (hopper lid
must be closed, vacuum switch must
be closed, snap disc closed, and feed
motor must be plugged in) Clear jam in
feed tube
Dirty appliance Clean appliance including the re pot,
exhaust path, and venting system
Igniterhasnopowerorisdefective Check igniter lead connections or
replace igniter
Exhaust probe not properly installed
Secure exhaust probe to exhaust
blowerhousing–keepingitswireaway
from hot surfaces
Igniterchamberpluggedwithdebris Clean igniter chamber
8RedFlashes:ExhaustOver-Temp
FeedMotorLockedOn Repair wire(s) and replace control
board
Non-approvedfuelused
Only use wood pellet fuel. Do not
enhance its performance with any other
combustible substance.
Convection blower dirty Clean impellers
Table 23.1
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quadra-Fire Outfitter I - Pellet at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quadra-Fire Outfitter I - Pellet in the language / languages: English as an attachment in your email.

The manual is 4.15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Quadra-Fire Outfitter I - Pellet

Quadra-Fire Outfitter I - Pellet User Manual - French - 30 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info