815524

Quadra-Fire Classic Bay 1200 Pellet Manual

10
Zoom out
Zoom in
Previous page
1/40
Next page
10 7027-802M 04/23
Figure 10.1
G. General Operating Information
1. Thermostat Calls For Heat
The appliance is like most modern furnaces; when the
thermostat calls for heat, your appliance will automatically
light and deliver heat. When the room is up to temperature
and the thermostat is satised, the red call light will go o󰀨
and the appliance will shut down (Figure 10.1).
2. Heat Output Controls
This appliance is equipped with a heat output control
switch that has three settings or burn rates; low, medium
and high. The appliance will turn on and o󰀨 as the
thermostat demands. When the thermostat calls for heat,
the appliance will start up on the high setting for the rst
4 minutes and 15 seconds, then automatically switch to
the burn rate for which it is set. If the appliance is set
at one of the lower settings, it will run quieter but take
longer to heat up an area than if it were set at a higher
burn rate. Regardless of the burn rate, when the area
is warm enough to satisfy the thermostat, the appliance
will shut o󰀨.
3. Fan Speed Switch
This switch will adjust the speed of the room distribution
air fan or convection blower on all three settings. This
means you have six di󰀨erent blower speeds available as
there is a high and low on each setting.
5. For your rst re it will be necessary to press the reset
button every two minutes until pellets start to drop into
the re pot, then press button 1 more time. This will ll the
feed system and allow the appliance to begin dropping
pellets. The appliance will continue to run as long as the
thermostat is calling for heat.
6. Once the appliance has ignited, let it burn for
approximately 15 minutes, then set the thermostat to the
desired room temperature. Adjust the heat output control
switch to the desired setting.
I. Fire Characteristics
A properly adjusted re with the heat output control switch
set on “high” has a short active ame pattern that extends
out of the re pot approximately 4 to 6 inches (102 to
152mm). If the re has tall ames with black tails and seems
somewhat lazy, the feed rate will need to be reduced. This
is done by sliding the fuel adjustment control rod down,
which will reduce the feed. If the re is not 4 to 6 inches
(102 to 152mm) tall, slide the fuel adjustment control rod up
to increase the feed. A medium and low setting will give a
shorter ame. The ame will rise and fall somewhat. This
is normal.
Fire Risk
Do NOT operate appliance:
• With appliance door open.
• Fire pot oor open.
• Cleaning slide plates open.
WARNING
Do NOT store fuel:
• Closer than required clearances to combustibles to
appliance
• Within space required for loading or ash removal.
H. Starting Your First Fire
1. A thermostat is required for proper operation of this
appliance. At this time, ll the hopper with pellets, set the
thermostat to its lowest setting. Plug the power cord into
nearby outlet.
2. The exhaust blower will stay on for approximately 10
minutes even though the thermostat is not calling for
heat. This is normal.
3. Locate the heat output control switch mounted on the
right side. Switch it to the high setting by pushing the top
of the switch in, then adjust the thermostat to its highest
setting. The red call light located on the upper right
corner of the right side panel will be on. This indicates
the thermostat is calling for heat (Figure 10.1).
4. The fuel feed system and the igniter should now be on.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quadra-Fire Classic Bay 1200 Pellet at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quadra-Fire Classic Bay 1200 Pellet in the language / languages: English as an attachment in your email.

The manual is 5.89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Quadra-Fire Classic Bay 1200 Pellet

Quadra-Fire Classic Bay 1200 Pellet User Manual - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info