Manual Pulsar Apex XD38 (page 7 of 55) (English, German, French, Italian, Spanish)

572608

Zoom out

Zoom in

1/55

10 11

џ Hold down the “MODE” (3) button to activate colour inversion mode

(functions “White hot” and “Black hot”). When function “White hot” is used,

warm objects are represented in shades of bright colour; “Black hot” renders

objects in shades of dark colour.

ZEROING

The sight features two zeroing methods - “one shot” zeroing and using

FREEZE function.

Zeroing should be done at operating temperatures, by following the order of

these steps:

One shot zeroing

џ Mount the rifle with the sight installed on a bench rest.

џ Set a target at a distance of about 100m.

џ Adjust the sight according to the instructions of Section 9 “OPERATION”.

џ Aim the firearm at the target using the mechanical sight.

џ Take a shot. If the point of impact does not match the aiming point, press the

controller (9) to enter menu M2 and rotate the controller to select option

“Zeroing” marked with icon.

џ Red auxiliary cross (C) appears in the centre of display. On the right of the

icon appear horizontal arrows and coordinated of the auxiliary cross .

џ Holding the reticle in the aiming point, by rotating

the controller (9) move the auxiliary cross (С)

horizontally or vertically relative to the reticle until

the auxiliary cross matches the point of impact (P)

(see pic.).

џ To switch between movement direction push the

controller (9) to hear a click. Vertical lines appear

next to the icon .

Note: the auxiliary cross moves only within the limiting frame (see pic.) that

defines its travel range: 200 clicks horizontally (+100/-100) and 200 clicks

vertically (+100/-100).

џ Exit submenu “Zeroing” with a long press of the controller button. Message

OK confirms successful operation. The reticle will now move to the point of

impact.

Attention! Do not turn off the sight before zeroing settings are saved,

otherwise your settings will be lost.

џ Take another shot - the point of impact should now match the aiming point.

џ The sight should now be zeroed-in for the specified distance.

Zeroing with “Freeze” function

џ Before using this function, please take a shot.

џ Select “Freeze” function in submenu M2.

џ Sight will prompt you to press any button on the sight or wireless control

within 30 seconds to freeze (memorize) the image. The status bar shows

corresponding icon.

џ Before pressing a button match the reticle of the sight with the aiming point

(as a rule - target centre). After button is pressed, the image “freezes” and a

limiting frame with an auxiliary cross appear. Rotating the controller, move

the auxiliary cross within the limiting frame until the cross matches the

point of impact.

Note. After the image freezes, you do not need to keep your weapon pointed

at the target.

џ Pressing the controller button allows you to switch direction of auxiliary

cross (horizontal or vertical). Long press of the controller button saves

zeroing settings and exits the menu.

џ Saving the settings is confirmed with “Ok” message displayed instead of

the coordinates.

џ After exiting the menu, the image returns to normal.

Note: zeroing parameters (coordinates X; Y) are saved in the sight's

memory as number 1 in the menu option “Weapon choice”. If you want to

zero in the sight using another weapon or another distance, select option 2 or

3 (details in the menu option “Weapon choice” section 12) and do the

zeroing.

OPERATING THE MENU

Long press of the controller – entering the menu.

Rotating the controller – menu navigation.

Short press of controller – entering menu option; selecting value in menu

option, exiting menu option or moving to the next parameter (clock mode).

Long press of controller – exiting menu option and menu (depending on

the cursor actual position). Automatic exit the menu takes place after more

than 10 seconds of inactivity (no navigation).

THE SIGHT HAS TWO MENUS

M1 – menu 1 (main menu);

М2 – menu 2 (additional menu);

Active submenu is highlighted with a frame . To switch to the other menu,

rotate the controller and move the cursor (the frame will be flashing), press

briefly the controller.

STATUS BAR

Status bar in the bottom part of the display shows information as follows:

1. Number of weapon choice (1,2,3):

2. Operation mode (“Rocks”,”Forest”,”Identification”):

3. Calibration modes - manual, semiautomatic and automatic:

4. 2x smooth digital zoom is on:

5. Image inversion is on:

6. Running time:

7. Battery charge level or connected external battery:

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pulsar Apex XD38 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 4,97 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pulsar Apex XD38 Manual

Product: