572608

Pulsar Apex XD38 Manual

9
Zoom out
Zoom in
Previous page
1/55
Next page
Defective pixel repair
џ When operating the thermal imager, there is a possibility of defective (dead)
pixels (bright or dark dots with constant brightness) appearing on the
detector which are visible on the image.
џ Thermal sights Apex provide an opportunity to repair defective pixels on the
detector using a software-based method.
џ Press and hold the controller (9) for two seconds to enter the menu.
џ Rotate the controller to select icon and press the controller.
џ Select icon in the pop-up submenu and press the controller.
џ A cross appears in the centre of display, coordinates (X;Y) of the
cross relative to the centre of display appear in the place of pop-up icons,
icons disappear.
џ Rotate the controller to align the cross with a defective pixel (if the alignment
is correct, the defective pixel should go out).
џ Switch direction of the cross from horizontal to vertical by a short press of the
controller.
џ After the centre of the cross is aligned with a defective pixel, press the MODE
(3) button to repair the pixel.
џ In case of success a short “OK” message appears in the place of the
coordinates.
џ Further on, move the cross to repair another defective pixel. When moving
the cross to the coordinates area, the latter goes to the lower right portion of
the display.
Return to default defective pixel pattern
џ If you wish to return to the default defective pixel pattern (i.e. restore all
defective pixels previously repaired), select icon in the pop-up submenu
and press the controller.
џ Options “Yes” and “No” appear on the right of the icon.
џ Rotate the controller to select “Yes” and press the controller.
џ If you choose not to return to default pixel pattern, select “No” and press the
controller.
џ To exit the main menu, keep the controller pressed for two seconds or wait 10
seconds to exit automatically.
Attention! One or two pixels in the form of bright white or black 1-2 pixels dots
are allowed on the display of thermal imager. These pixels cannot be repaired
and are not a defect.
Restore of default settings
To return to default settings:
џ Rotate the controller to select “Default settings”. Press the controller button.
џ To activate return to default settings, rotate the controller to select “Yes”,
press the controller button.
The following settings will return to their original status before the changes:
Operation mode – “Rocks”;
Calibration mode – automatic;
Weapon selection – 1;
Selection of preloaded reticle – 1 (for all weapon types);
Reticle colour – black;
Brightness of onscreen symbols (menu and status bar) – 5;
Video output – off;
Display brightness level – 12;
Display contrast level – 12;
Digital zoom – x1;
Image inversion – off;
Function “PiP” – off
To cancel return to default settings, select “No” and press controller button to
confirm.
Note: zeroing coordinates do not return to default for all types of weapon.
VIDEO OUTPUT
Video output is designed to connect external recording devices and to
transmit video signal to monitors, TV sets etc.
џ Connect the plug (13) of the cable to the jack (10) of the sight by matching
the notch in the plug connector and the protrusion of the jack (10) (see the
scheme).
џ Secure the cable by turning clockwise the locking ring of the plug (13).
џ Connect the signal receiver to the jack (14) of the cable.
џ Turn on the sight – image will appear on the external device. Please make
sure the external device is in the AV mode.
џ To record video, you can use video recorders such as Yukon MPR
(#27041) / CVR640 (#17044) and others.
Note: it is not recommended to attach the CVR640 on the sight because the
video recorder is not designed for heavy shock resistance.
WIRELESS REMOTE CONTROL
The wireless remote control duplicates functions of the sight, calibration
function and digital zoom/PiP function.
It has three buttons:
џ Button “ON” (16) – turning the sight on/off (press for two seconds to
deactivate).
џ Button “CAL” (17) – image calibration.
џ Button “ZOOM/PiP” (18) – digital zoom on/off or function “PiP” on/off.
To start using the wireless remote control you will need to activate it:
џ Turn on the scope and select menu option “RC activation” (icon ).
џ Press controller button, a message “WAIT” will show up and countdown
will start within which you need to press any button of the RC.
џ If the activation is successful, a message “Complete” will show up next to
icon. The RC is ready for use.
џ If the RC does not work, replace the battery. To do this, unscrew the screws
on the rear panel of the RC, remove the cover, pull out the old battery and
insert a new CR2032 battery.
WEAVER RAIL 7/8“
With the help of the Weaver rail (11) you can attach accessories such as:
џ External power supply EPS3 (#79111).
14 15
13
14
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pulsar Apex XD38 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pulsar Apex XD38 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 4,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info