782214

Proxxon TG 125-E Manual

13
Zoom out
Zoom in
Previous page
1/68
Next page
- 13 -
5 Before work
5.1 Setting up your disc grinding machine
(fig. 2):
Note:
When setting up the machine, make sure that the
ground below it is level and secure! A secure stand is
indispensable for working with the machine!
Note:
When setting up and fixing the machine, always dis-
connect the mains plug to prevent the disc being
started up accidentally. Risk of injury!
Caution:
During all adjusting and assembly work, such as
when adjusting the angle stop or when attaching or
removing the grinding table, disconnect the mains
plug to prevent the device from starting up uninten-
tionally!
The disc grinding machine can be operated in two
different positions: Once in the normal horizontal
position or standing vertically (for sharpening tools
and blades for example).
In both positions, the machine should be securely
clamped with the enclosed vice, as shown in fig. 2.
5.2 Removing and inserting the grinding
table (fig.3):
Caution:
Before removing and inserting the grinding table,
always disconnect the mains plug to prevent the disc
being started up accidentally. Risk of injury!
Normally, your TG 125/E is operated with the
attached grinding table (as in delivery condition).
Additionally, there is also the possibility, where
required, of removing the grinding table, if this is nec-
essary for certain tasks or for changing the grinding
wheels.
Caution:
Please note that when working particularly in the
operating mode without the grinding table, always
make sure to control the work piece by holding it
firmly and securely in order to prevent it from being
flung about.
Use the machine in the horizontal position with
attached grinding table, if possible!
1. Remove Allen head screw 1
2. Remove the grinding table with grinding table
holder 2 by pulling out from the front
3. To insert, simply push into the normal position
4. Turn in Allen head screw 1 again
Caution:
If the grinding disc is blocked due to a work piece
that is jammed between the grinding disc and the
grinding table, immediately shut off the device using
the On/Off switch and disconnect the mains plug.
Only put the device back into operation after the
jammed work piece has been removed!
5.3 Affixing and replacing grinding wheels
(fig. 4):
Note:
Before affixing or replacing the grinding wheels,
always disconnect the mains plug to prevent the disc
being started up accidentally. Risk of injury!
Two grinding wheels in each of the grain sizes 80,
150 and 240 are supplied as initial equipment with
your disc grinding machine; these can also be easily
obtained as spare parts. It is therefore no problem to
change wheels, whether because of wear or because
discs with various grain sizes are required when
working.
Caution:
When replacing the wheels, it is advisable to remove
the grinding table as described in the previous sec-
tion!
1. Remove the rear protective foil above the adhe-
sive surface from the desired wheel,
2. Push the wheel evenly and bubble-free onto the
grinding disc.
3. To replace, simply remove the grinding wheel
again and push on the new wheel.
Accessories
For more detailed information on accessories, please
request our device catalogue from the address speci-
fied on the last page in the warranty information.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Proxxon TG 125-E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Proxxon TG 125-E in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Turkish, Spanish as an attachment in your email.

The manual is 3.16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info