Manual Proxxon TG 125-E (page 14 of 68) (English, German, Dutch, Danish, French, Italian, Polish, Swedish, Turkish, Spanish)

782214

Zoom out

Zoom in

1/68

Please note in general:

Proxxon bits and cutters have been designed to work

with our machines, which makes them optimal for

their use.

We will not assume any liability whatsoever for the

safe and proper function of our devices when using

third-party bits and cutters!

5.4 Adjusting the grinding table angle

(fig. 5):

Caution:

Before adjusting the grinding table, always discon-

nect the mains plug to prevent the disc being started

up accidentally. Risk of injury!

1. Loosen rotary knob 1 At the same hold rotary

knob 2

2. Swing grinding table 3 into the desired angle posi-

tion and check the set value on angle scale 4.

3. Tighten rotary knob 1. At the same hold rotary

knob 2

5.5 Connecting the dust exhaust (fig. 6):

Caution:

Before connecting the dust exhaust, always discon-

nect the mains plug to prevent the disc being started

up accidentally. Risk of injury!

It is recommended to always work with the dust

exhaust! This not only guarantees clean working, it

also reduces the hazardous effect of some dusts!

1. Push adapter piece 1 onto connecting piece 2 of

the machine

2. Push rubber adapter 3 onto adapter piece 1

3. Insert vacuum cleaner nozzle 4 into rubber

adapter 3

4. Switch on vacuum cleaner when working

Another small tip:

When using the Proxxon CW-matic vacuum cleaner,

manual switching on and off is no longer necessary.

The CW-matic is fitted with an automatic control

device; it automatically switches on and off when the

power tool is switched on and off. The same effect

can be obtained with traditional vacuum cleaners by

using our vacuum control device.

6 Working with the TG 125/E disc grinding

machine

Caution:

Please note that the grinding disc turns to the left! If

you use the left side when working with the attached

grinding table, the work piece can be guided easily

and securely, thus effectively preventing it from being

hurled away!

Caution:

When grinding metallic work pieces, such as when

grinding knife blades for example, or when grinding

stone or ceramics the material to be ground can

become very hot! Do not hold the material to be

ground near the grinding surface in order to avoid

burns!

Caution:

Wear suitable gloves to avoid abrasions especially

when working with coarse sandpaper and when pro-

cessing smaller work pieces!

1. If mitres are to be ground, adjust the grinding

angle as described above

2. Insert the mains plug

3. Switch on the machine at On-Off-Switch

4. Set the required speed on the speed control but-

ton (pos. 3, fig. 1)

Please adjust the size of the work piece to the size of

the machine! A work piece that is too large and too

heavy can overburden the drive or the construction of

the machine and cause damage or injuries!

6.1 Working with the angle stop (fig. 7):

If, for example, the ends of somewhat thinner strips

are ground for mitre, it is advantageous to use the

angle stop included in the scope of delivery.

1. Loosen knurled screw 1

2. Set the desired angle on scale 2

3. Turn the knurled screw tightly and insert into the

intended table groove

4. Guide the desired workpiece up to the stop

against the grinding wheel as shown in the illus-

tration

- 14 -

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Proxxon TG 125-E in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Turkish, Spanish as an attachment in your email.

The manual is 3.16 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Proxxon TG 125-E Manual

Product: