782209
8
Zoom out
Zoom in
Previous page
1/16
Next page
-8-
Adjustment of the milling spindle
The milling spindle of the PF 230 canbe height-adjusted in
2 ways:
1. By using the fine feed 1 (Fig. 9)
2.By using the drilling lever 2
Verticaladjustment viafine tolerance feed
1. Loosen screw 3 (Fig. 9).
2.Adjust to the desired height using the hand wheel 1
(1 rotation corresponds to 1 mm feed).
3.Screw 3 must always be tightened again.
Feed via the drilling lever
1. Loosen screw 4(Fig. 9).
2.Loosen screw 6 and set scale 5 to zero.
3.Retighten screw 6.
4. Adjust to the desired height using the drill lever 2.
5. Retighten screw 4.
Note:
The drilling lever is not just used for height adjustment.It
canbealsobe used for drilling. Do not tighten the screw 4
when drilling.
Swivelling the milling spindle
The entire milling spindle canbe swivelled around twoaxes.
To swivel around the verticalaxis, release screw 4(Fig. 6)
and swivel the column completely into the required position.
Then retighten the screw.To swivel around the lateral
axis, release screw 1 (Fig. 10)and swivel the milling spindle.
Set the required number of degrees on the scale 2 and
retighten screw 1.
Assembly of the clamping devices for the milling machine:
Impor tant
Never insert the collet chuckalone into the spindle! Always
engage the collet chuck into the nut first!Always ensure
that collet chuckand milling tool have the correct diameter
for proper fit.
Please note:Further collet chuck dimensions areavailable
as accessory equipment in addition to thosecollet chucks
supplied. Theseare listed in our equipment catalogue.
Pleaseconsult our customer service department for further
information.
W arning:
Use only accessories recommended for this milling machi-
ne. Follow the instructions that accompany accessories.
Use of improper accessories may cause hazards!
1. Loosen union nut (7, see Fig. 1).
2.Place desired collet chuck 2:(see Fig. 11) into union nut
1and allow to engage.
3.Insert union nut withcollet chuck in the spindle and turn
sightly by hand.
4. Insert milling tool intocollet chuck.
5. Lock milling spindle using the spanners supplied and
tighten union nut.
6.To removecollet chuck loosen union nut and remove
milling tool.
7.Now remove union nut withcollet chuckcompletely from
milling spindle.
8. Disengage collet chuck using light sideways pressure 3
(Fig. 11) and remove from union nut.
Setting the spindle rotational speed
A total of 6 spindle speeds may beadjusted by shifting the
V-belt (Fig. 12 a/b): 280,540, 780,910,1710, and 2500
rpm.
Note:
Tighten belt only lightly!A belt installed too tightly places
excessive loads on the motor and machine mechanical
system!
1. Loosen knurled screw 4 (Fig.13)and open cover 7.
2.Loosen screw 5 using anAllen key by approx. 2 turns in
order to releasebelt pulley tension.
3.Placebothbelts in the desired position.
4. Press belt pulley 1 outwards with the belt tightener 8
below the gear wheels until the belt is tight.Tighten
screw 5.
5. Should bothbelts be tensioned unevenly, the upper belt
may be tensioned separately.To do so,loosen screw 2
and push motor 3 outwards until upper belt is tensioned.
6.Retighten screw 2.
Important:
The belt cover must always beclosed during operation.
Only tension the belts lightly.A too highly tensioned belt
strains the motor and the mechanics of the machine!
Replacement belts areavailable from the PROXXON central
service team (address on the rear side of these
instructions).
Working with the machine
Important:
The belt cover must always beclosed during operation.
Impor tant
Always wear protective goggles when milling. Take great
care to observe the safety regulations above.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Proxxon FF 230 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Proxxon FF 230 in the language / languages: English as an attachment in your email.

The manual is 1.69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info