782209
9
Zoom out
Zoom in
Previous page
1/16
Next page
-9-
1. Securely fasten the work piece using clamps,in a vice,
or to the support of the lathe chuck. Alternatively, you
canclamp the work piece in amachine viceand mount
the vice on the work table using the T-grooves.
2.Adjust desired milling depth.
3.Tighten clamping screws 3 and 4 (Fig. 9).
4. Ensure that the milling tool does not touch the work
piece.
5. Ensure that the proper spindle speed has been adjusted.
6.Switch on milling machine at switch 3 (Fig. 1).
7.Work using a suitable feed
Note:
The feed must always take placeagainst the cutting
direction of the milling cutter (also refer Fig.14.)
Impor tant!
Always provide feed by hand only!When using the milling
machine in conjunction with the lathe PD 230/E, feed action
must not occur via the lathe's automaticfeed. Risk of injury!
Repair and maintenance
Impor tant:
Disconnect mains power beforecleaning and maintaining
unit.
Do not usecompressed air when cleaning.
Setting compound-type table guide play
If, after a time, the compound-type table guide is found to
have too much or too little play, the play canbe reset using
the adjusting screws 2 (Fig. 15). For this purpose,loosen
adjustment screw lock nuts 1and screw in all adjustment
screws evenly until play is eliminated. Retighten lock nuts
afterwards.
Setting compound-type table spindle play
If play of the spindles increases, release the nut 1 using a
socket spanner 2 or i. e. a ratchet. (Fig. 16)approx. one half
turn. Then turn the hand wheel to the right hand direction
until the play has been eliminated. Now retighten the nut 1
firmly, while holding the handwheel in the position it has
been adjusted.
Note:
See exploded view,page 10: Where necessary,play in the
individual spindle threads canalsobeachieved by slightly
tightening the spindle nut, Item 3, with the bolt, Item 25.
W arning
Toavoid fire or toxic reaction,never use gasoline,naphtha,
acetone,lacquer thinner,or similar highly volatile solvents to
clean the Milling machine.
Do not allow brake fluids,gasoline,or penetrating oils to
come in contact with the plasticparts.They contain
chemicals that can damage or destroy plastics.
Turn switchOFF and always remove plug from power
sourcebefore making any adjustments or repairs.
All electrical or mechanical repairs should be done only by
qualified service technicians.
When servicing use only PROXXON replacement parts.Use
of any other parts may createahazard or cause product
damage.
Any attempt to repair or replace electrical parts on this lathe
may createahazard unless repair is done by aqualified
service technician. Repair service is available at your
PROXXON servicecenter (You find the address at address
at the back of this manual)
Lubricating the machine
To ensurealong service life of your machine,please
observe the lubrication diagram in Fig. 17 (A: Lubricate
each time before use / B: Lubricate onceamonth). Only
useacid-free machine oil for lubrication.
Only useacid-free machine oil.
Replacement of the belts
Important:
Use only accessories recommended for this lathe. Follow
the instructions that accompany accessories.Use of
improper accessories may cause hazards.
If the belts become worn, you canchange them yourself.
Replacement belts areavailable from the PROXXON central
service team (address on the rear side of these
instructions).
•Unscrew screw 5 (Fig.13) to release the belt pulley 1.
•Unscrew the 3 screws 6 (Fig.13)and lift out the motor.
•You can now removeand replace the belts.
•Re-assemble in reverse order.
After use
Attention:
Disconnect milling machine mains plugbeforecleaning!
Cleancompound-type table and milling machine using a
soft clothand brushafter use. Then lightly oil the guides
and distribute the oil by moving the table. Never use
compressed air for cleaning the compound-type table as
cuttings entering the guides in this manner could destroy
the guides.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Proxxon FF 230 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Proxxon FF 230 in the language / languages: English as an attachment in your email.

The manual is 1.69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info