782211
9
Zoom out
Zoom in
Previous page
1/24
Next page
NEVER attempt to free a stalled saw blade without
first turning the saw OFF and disconnecting the saw
from the power source.
PROVIDE ADEQUATE SUPPORT to the rear and
sides of the saw table for wide or long work pieces.
Use a sturdy „outrigger“ support if a table extension
more than 24 inches long is attached to the saw.
AVOID KICKBACKS (work thrown back toward you)
by:
A. Keeping blade sharp.
B. Keeping rip fence parallel to the saw blade.
C. Keeping riving knife, anti-kickback pawls, and
blade guard in place and operating.
D. Not releasing the work before it is pushed all the
way past the saw blade using a push stick.
E. Not ripping work that is twisted or warped or
does not have a straight edge to guide along the
fence.
AVOID AWKWARD OPERATIONS AND HAND PO-
SITIONS where a sudden slip could cause your hand
to move into the cutting tool.
CHECK WITH A QUALIFIED ELECTRICIAN or serv-
ice personnel if the grounding instructions are not
completely understood or if in doubt as to whether
the tool is properly grounded.
USE ONLY CORRECT ELECTRICAL DEVICES: 3-
wire extension cords that have 3-prong grounding
plugs and 3-pole receptacles that accept the tool’s
plug.
DO NOT MODIFY the plug provided. If it will not fit
the outlet, have the proper outlet installed by a quali-
fied electrician.
USE ONLY RECOMMENDED ACCESSORIES listed
in this manual or addendums. Blades must be rated
for at least 6,0000 rpm. Use of accessories that are
not listed may cause the risk of personal injury. In-
structions for safe use of accessories are included
with the accessory.
DOUBLE CHECK ALL SETUPS. Make sure blade is
tight and not making contact with saw or workpiece
before connecting to power supply.
MAKE SURE THE WORK AREA HAS AMPLE
LIGHTING
to see the work and that no obstructions will interfere
with safe operation BEFORE performing any work
using the table saw.
ALWAYS TURN OFF SAW before disconnecting it,
to avoid accidental starting when reconnecting to
power supply.
SAVE THESE INSTRUCTIONS. Refer to them fre-
quently and use to instruct other users. If you loan
someone this tool, loan them these instructions also.
Further safety instructions
This machine is for indoor use only. Do not expose to
rain or use in damp locations.
Use only accessories recommended for this table
saw. Follow the instructions that accompany acces-
sories. Use of improper accessories may cause haz-
ards.
Do not attempt to modify this tool or create acces-
sories not recommended for use with this tool. Any
such alternation or modification is misuse and could
result in hazardous condition leading to possible seri-
ous injury.
To avoid injury from unexpected starting or electrical
shock, do not plug the power cord into a power
source receptacle during unpacking and assembly.
This cord must remain unplugged whenever you are
working on the table saw.
If any part is missing or damaged, do not plug the
table saw in until the missing or damaged part is re-
placed, and assembly is complete. To avoid electrical
shock, use only identical replacement parts when
servicing grounded tools.
For your safety, never connect the plug to the power
source receptacle until the assembly and adjustment
steps are completed, and you have read and under-
stood the safety and operating instructions.
To avoid injury from accidental start, make sure the
switch is in the OFF position and the plug is not con-
9
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Proxxon FET at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Proxxon FET in the language / languages: English as an attachment in your email.

The manual is 1.55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info