782211
8
Zoom out
Zoom in
Previous page
1/24
Next page
smaller the gage number, the heavier the cord.
Exception No. 1: The reference to the table and
the table itself may be omitted if a statement in-
dicating the appropriate gage and length is incor-
porated into the instruction. Exception No. 2: The
information regarding extension cords need not
be provided for a permanently connected tool.
10. WEAR PROPER APPAREL. Do not wear loose
clothing, gloves, neckties, rings, bracelets, or
other jewelry which may get caught in moving
parts. Non-slip footwear is recommended. Wear
protective hair covering to contain long hair. Ex-
ception: The reference to gloves may be omitted
from the instructions for a grinder.
11. ALWAYS USE SAFETY GLASSES. Also use face
or dust mask if cutting operation is dusty. Every-
day eyeglasses only have impact resistant
lenses, they are NOT safety glasses.
12. SECURE WORK. Use clamps or a vise to hold
work when practical. It’s safer than using your
hand and it frees both hands to operate tool.
13. DON’T OVERREACH. Keep proper footing and
balance at all times.
14. MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for best and safest performance. Fol-
low instructions for lubricating and changing ac-
cessories.
15. DISCONNECT TOOLS before servicing; when
changing accessories, such as blades, bits, cut-
ters, and the like.
16. REDUCE THE RISK OF UNINTENTIONAL START-
ING. Make sure switch is in off position before
plugging in.
17. USE RECOMMENDED ACCESSORIES. Consult
the owner’s manual for recommended acces-
sories. The use of improper accessories may
cause risk of injury to persons.
18. NEVER STAND ON TOOL. Serious injury could
occur if the tool is tipped or if the cutting tool is
unintentionally contacted.
19. CHECK DAMAGED PARTS. Before further use of
the tool, a guard or other part that is damaged
should be carefully checked to determine that it
will operate properly and perform its intended
function — check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting, and any other conditions that may af-
fect its operation. A guard or other part that is
damaged should be properly repaired or re-
placed.
20. DIRECTION OF FEED. Feed work into a blade or
cutter against the direction of rotation of the
blade or cutter only.
21. NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN POWER OFF. Don’t leave tool until it
comes to a complete stop.
Additional safety instructions for table
saws:
ALWAYS USE BLADE GUARD, RIVING KNIFE,
AND ANTI-KICKBACK PAWLS on all „through-saw-
ing“ operations. Through-sawing operations are
those in which the blade cuts completely through the
workpiece as in ripping or crosscutting. Keep the
blade guard down, the anti-kickback pawls down,
and the riving knife in place over the blade.
ALWAYS SECURE WORK firmly against rip fence or
miter fence.
ALWAYS USE A PUSH STICK FOR RIPPING NAR-
ROW STOCK. A push stick is a device used to push
a workpiece through the blade instead of using your
hands. Size and shape can vary but the push stick
must always be narrower than the workpiece to pre-
vent the push stick from contacting the saw blade.
When ripping narrow stock, always use a push stick,
so your hand does not come close to the saw blade.
Use a featherboard and push blocks for non-through
cuts.
NEVER perform any operation „freehand“ which
means using only your hands to support or guide the
workpiece. Always use either the rip fence or miter
fence to position and guide the work.
NEVER stand or have any part of your body in line
with the path of the saw blade.
NEVER reach behind, over, or within three inches of
the blade or cutter with either hand for any reason.
MOVE THE RIP FENCE out of the way when cross-
cutting.
NEVER use rip fence as cutoff gage when crosscut-
ting.
8
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Proxxon FET at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Proxxon FET in the language / languages: English as an attachment in your email.

The manual is 1.55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info