Manual Protool RGP3 (page 8 of 63) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

490678

Zoom out

Zoom in

1/63

Putting into Operation

The voltage specifications on the rating plate must

correspond with the mains voltage. Equipment

marked with 230 V can also be connected to 220 V /

240 V.

Auxiliary Handle

In the interests of safety, the auxiliary handle (4)

should always be used. Screw the auxiliary handle

to the right or the left of the machine head depend-

ing on the work method.

Switching on and off

Switching on:

Slide ON/OFF switch (3) forwards and depress at

the front until switch locks into position.

Switching off:

Depress ON/OFF switch (3) at the rear-switch

jumps back to its initial position.

Dust Vacuuming

Grinding work may be performed only in conjunc-

tion with a suitable vacuum cleaner. For materials

detrimental to health, the regulations of the trade

association (dust classes) for the selection of the

vacuum cleaner are to be observed.

Vacuum Opening

The vacuum opening (10) server for the connecting

of a suitable vacuum cleaner.

For the connection to the vacuum hose, the use of

the connection sleeve No. 614 109 is recommended

(optional accessory).

Vacuuming Hood with Brush Ring

The best dust vacuuming results are achieved with

the vacuuming hood (2) provided with the machine.

For working close to edges, the vacuuming hood

can be removed. The vacuuming hood is held with

three spring-loaded balls on the head of the gearbox

housing and can be removed and remounted with-

out tools.

Replacing the Brush Ring

The brush ring (5) further improves the vacuuming

performance and should always be mounted. By

loosening the four screws (8), a brush ring worn

from working can be replaced. Press in the new

brush ring (No. 614 268) and retighten the screws.

Replacing the Grinding Tools

❑

Before all work on the machine itself, pull the

plug from the socket!

Place the machine on a firm surface.

Before replacing the grinding tools, free the screw

heads (6) from dust and dirt.

To block the drive unit, press the spindle locking

button (1).

With the Torx key (9), loosen the three screws (6).

The screws (6) have left-hand threads!

Take out the grinding tools (7) and clean the tool

holders.

The grinding tools should always be replaced as a

complete set. Do not use grinding tools with differ-

ent degrees of wear.

For the mounting of the grinding tools, take care

that they are placed exactly in the mounting point of

the drive spindles.

❑

Use only the grinding tools available from and

approved by the manufacturer.

❑

Before returning to operation, check the firm

seating of the grinding tools and flawless true

running. Out of round grinding tools should not

be used.

❑

The spindle locking button may be operated only

when the machine is at a standstill.

Working Method

Apply the machine while switched on to the mate-

rial surface and move in a parallel or circular

manner in the longitudinal or lateral direction. Do

not work diagonally over the edges.

The working performance when grinding is deter-

mined primarily by the grinding tools selected as

well as the application pressure.

Excessively increasing the application pressure

does not lead to increased grinding performance but

only to heavy wear of the machine and the grinding

tools.

RGP 3 - GB Seite 8 Freitag, 16. Juli 1999 11:15 11

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Protool RGP3 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,73 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Protool RGP3 Manual

Product: