490605

Protool PDP 20-4 DEC FF Manual

14
Zoom out
Zoom in
Previous page
1/87
Next page
14
DRP 18-4 DEC FF/ PDP 20-4 DEC FF
GB
7.3 Selecting the operating mode
(only PDP 20-4 DEC FF)
Fastening / Drilling
Set the selector switch [1-5] to the
drill bit symbol.
When fastening
, always remember
to work in 1st gear and at low speeds.
Impact drilling
Set the selector switch [1-5] to the
hammer symbol.
X
The machine was designed for impact
drilling into tiles, masonry and stone.
8 Tool holder, attachments
8.1 Tool chuck CENTROTEC WH-CE
[3]
The tool chuck CENTROTEC WH-CE allows
you to change tools with a CENTROTEC
shank in a matter of seconds.
X
Always use a CENTROTEC tool chuck to
clamp CENTROTEC tools.
8.2 Chuck [4]
The drill chuck retains the drill or screwdriver
bit.
X
Before initial use:
apply a coat of multi-
purpose grease to the drill spindle.
8.3 Angle attachment [5]
The angle attachment (partly as an accesso-
ry) allows the user to drill and fasten at right
angles to the machine.
X
Before initial use:
apply a coat of multi-
purpose grease to the drill spindle and
gearbox extension.
8.4 Depth stop [6]
The depth stop (partly as an accessory) al-
lows the user to insert screws to a predefined
depth. You can set the dimension by which
the screw head protrudes above or is re-
cessed below the surface of the workpiece.
Depth setting
Turn the housing [6-1] to set
the desired fastening depth.
Each detent position chang-
es the fastening depth by 0.1
mm.
Sleeve A/B must be removed before a screw
can be unscrewed.
8.5 Tool holder in the drill spindle
[7]
Bits can be inserted directly in the hexagon
socket holder on the drill spindle to shorten
and reduce the weight of the machine.
9 Working with the machine
Please observe all mentioned safety in-
formations and the following rules
when working:
– Only use tools designed for the specified
maximum speed.
– Only sharp tools ensure efficient drilling
and prevent machine overload.
– Always use faultless, sharpened HSS drill
bits (HSS: High Speed Steel) when drilling
into metal.
– Do not cause the machine to seize through
overloading.
– Always switch off the machine before plac-
ing on the nut/screw.
–Caution: when inserting long screws, there
is a risk the bit may slip from the screw
head and cause injury.
– Machine vice: clamp the workpiece secure-
ly in a machine vice, for example, before
drilling to prevent the workpiece from
turning and causing accidents.
9.1 Bit store [1-1]
The magnetic bit store is designed for hold-
ing bits or bit holders.
WARNING
Risk of injury, electric shock
X
Always pull the plug out of the socket be-
fore performing any type of work on the
machine!
CAUTION
Tool has sharp edges and can cause cut-
ting injuries during a tool change.
X
Wear protective gloves!
CAUTION
Risk of injury
X
Clamp the tool centrally in the drill chuck!
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Protool PDP 20-4 DEC FF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Protool PDP 20-4 DEC FF in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info