Manual Protool DRC 12-4 TEC LI (page 13 of 104) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish)

79301

Zoom out

Zoom in

1/104

Table of contents

The term “power tool” in the warnings refers to

your mains-operated (corded) power tool or bat-

tery-operated (cordless) power tool.

4.2 Machine-related safety

instructions

- Hold power tool by insulated gripping sur-

faces, when performing an operation where

the cutting accessory may contact hidden

wiring or its own cord. Cutting accessory con-

tacting a ”live” wire may make exposed metal

parts of the power tool ”live” and could give the

operator an electric shock.

- The charger and power tool are not intended for

use by persons (including children) with limited

physical, sensory or mental ability or without

sufﬁ cient experience and/or knowledge, unless

they are supervised by a person responsible

for their safety or have been instructed on how

the charger or power tool is to be used. Chil-

dren should always be supervised to ensure that

they do not play with the charger or the power

tools.

- Take care when drilling into walls as there is a

danger of rupturing concealed gas/water pipes

or cutting through power cables.

- Do not open the battery pack or the charger.

Even after disconnection from the mains, there is

still a high capacitor voltage inside the charger.

- Make sure that metal objects (such as metal

chips) do not collect in the battery pack retain-

ing slots or enter the machine through the air

vent slits (danger of short circuit).

- Protect the battery pack from excessive heat or

constant heat sources such as sunlight or naked

ﬂ ames. There is a risk of explosion.

- Never use water to extinguish burning LiIon bat-

tery packs, always use sand.

4.3 Emission levels

Levels determined in accordance with EN 60 745

are typically:

Sound pressure level L

= 73 dB (A)

Noise level L

= 84 dB (A)

Uncertainty K = 3 dB

CAUTION

Operating noise

Damage to hearing

► Use ear protection!

Vibration emission value a

(vector sum for three

directions) and uncertainty K measured in accord-

ance with EN 60 745:

Screwing a

h, S

< 2.5 m/s

Drilling in metal a

h, D

= 5.6 m/s

Uncertainty K = 1.5 m/s

Declared total value of vibrations was measured

according to standard measure method and can

be used for comparison one powertools with the

others.

2 Machine features

[1-1] Bit holder

[1-2] ON/OFF switch

[1-3] Right/left switch

[1-4] Gear switch

[1-5] Torque thumbwheel

[1-6] Clamp for attaching to the belt

[1-7] Lighting button

[1-8] LED light

[2-1] Buttons for releasing the battery

[3-1] LED

[3-2] Battery pack

Not all of the accessories illustrated or described

are included as standard delivery.

3 Intended use

Cordless drills are suitable for drilling into metal,

wood, plastics and similar materials as well as in-

serting and tightening screws.

The BC 3 charger is designed for charging the bat-

tery packs listed.

The user is responsible for any damages and in-

juries caused by use which does not conform to

the intended purpose; including any damages and

wear caused by permanent industrial operation.

4 Safety instructions

4.1 General safety instructions

WARNING! Read all safety warnings and

all instructions. Failure to follow the warn-

ings and instructions may result in electric

shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future

reference.

1 Symbols ............................................ 12

2 Machine features ................................ 13

3 Intended use ...................................... 13

4 Safety instructions .............................. 13

5 Commissioning ................................... 14

6 Machine settings ................................. 14

7 Tool holder, attachments ...................... 14

8 Operation .......................................... 15

9 Service and maintenance ..................... 16

10 Transport ........................................... 16

11 Accessories ........................................ 17

12 Disposal ............................................ 17

13 Warranty ........................................... 17

14 EU Declaration of Conformity ................ 17

CA BE REPEATED FOR DRILLING MACHINE RUN FOR 2 SECOND THEN STOP. THIS CAN BE DONE NUMEROUS TIMES. BATTERY CHARGER INDICATES THAT BATTERIES ARE FULLY CHARGED. BEEN INACTIVE NOW FOR 3 YEARS AND STILL REPEAT THE SAME PROBLEM. Submitted on 11-1-2023 at 12:19
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Protool DRC 12-4 TEC LI in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Protool DRC 12-4 TEC LI Manual

Product: