79301

Protool DRC 12-4 TEC LI Manual

15
Zoom out
Zoom in
Previous page
1/104
Next page
15
Changing tools
Turn the clamping sleeve [4-3] anticlockwise to
open the clamping jaws.
The arrow on the chuck shows the direction to turn
to open it.
Insert the tool into the chuck.
CAUTION
Risk of injury
► Clamp the tool centrally in the chuck!
Turn the clamping sleeve [4-3] clockwise to clamp
the tool.
7.2 Tool chuck CENTROTEC
The tool chuck CENTROTEC allows you to change
tools with a CENTROTEC shank in a matter of sec-
onds.
► Always use a CENTROTEC tool chuck to clamp
CENTROTEC tools.
CAUTION
Risk of cutting injuries when changing the
tool!
► Wear protective gloves!
Attaching the CENTROTEC
Pull the release ring [5-1] forwards.
Attach the tool chuck to the drill spindle [4-1].
Release the ring [5-1].
Detaching the CENTROTEC
Pull the release ring [5-1] forwards.
Remove the tool chuck.
Changing tools
To fi t or remove a tool with a CENTROTEC shank,
pull back the orange ring [5-2].
When attaching the tool, rotate until the hexagon
shank engages in the hexagon holder on the drill
spindle.
Release the ring [5-2].
7.3 Angle attachment
The angle attachment allows you to work (drill,
fasten) vertically in relation to the longitudinal axis
on the machine.
Fitting the angle attachment
► Before fi rst use, the spindle [4-1] and gearbox
neck [6-1] should be painted with a thin layer
of multipurpose grease.
Release the lever of the angle attachment.
Fit the attachment right down onto the neck of the
gearbox so that the recess in the attachment sits
on the protruding part of the gearbox.
Secure the attachment lever.
The angle attachment can be positioned through
30°.
Attaching/Detaching the chuck
The chuck is secured to the shaft of the angle at-
tachment and the drill spindle on the machine in
the same way.
7.4 Depth stop DC UNI FF
The depth stop allows you to insert a screw to a
defi ned depth. You can set the dimension to which
the screw head is to project over the workpiece, or
to which it is to be countersunk in the workpiece.
Assembly
Place the depth stop onto the spindle of the screw-
driver [8-1].
Pull the release ring [8-2] forwards.
Turn it until the hexagonal pin of the stop engages
in the internal hexagon support of the machine.
Press to stop onto the machine spindle. Let go of
the release ring.
Disassembly
Pull the release ring [8-2] forwards and then re-
move the depth stop from the spindle.
Tool change
Take sleeve A or B off the depth stop. Insert the
corresponding bit or plug-in bit adapter in the mag-
netic holder [8-3]. Refi t sleeve A or B.
Setting the depth
Set the desired screw-in
depth by turning the hous-
ing [8-4] – see symbol on
the holder. Each notch
stage alters the screw-in
depth by 0.1 mm.
Removing the screws
If you wish to unscrew a screw again, sleeve A or
B must be removed. Now set the screwdriver to
counterclockwise direction of rotation and unscrew
the screw.
7.5 Auxiliary handle
Fit the auxiliary handle right down onto the neck
of the gearbox so that the recess in the handle sits
on the protruding part of the gearbox.
Tighten the auxiliary handle by twisting the grip.
The auxiliary handle can be positioned through
30°.
The drilling depth can be set with the depth stop
[7-2].
7.6 Tool holder in the drill spindle
Bits can be inserted directly in the hexagon socket
holder on the drill spindle [4-1] to shorten and
reduce the weight of the machine.
8 Operation
Press the ON/OFF switch [1-2] to switch on the
machine.
The speed of the machine depends on how far the
ON/OFF switch is pressed in.
… 15 …


Need help? Post your question in this forum.

Forumrules
1

Forum

protool-drc-12-4-tec-li

Reset search

  • CA BE REPEATED FOR DRILLING MACHINE RUN FOR 2 SECOND THEN STOP. THIS CAN BE DONE NUMEROUS TIMES. BATTERY CHARGER INDICATES THAT BATTERIES ARE FULLY CHARGED. BEEN INACTIVE NOW FOR 3 YEARS AND STILL REPEAT THE SAME PROBLEM. Submitted on 11-1-2023 at 12:19

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Protool DRC 12-4 TEC LI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Protool DRC 12-4 TEC LI in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info