Manual Protool CSP 56 (page 20 of 136) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish)

110272

Zoom out

Zoom in

1/136

Non-ferrous Metals

Use only a suitable and sharp saw blade.

This ensures a clean cut and prevents jam-

ming of the saw blade.

Apply the machine running to the workpiece,

carefully start sawing and then saw with

slow feeding and without interruption.

For proﬁ les, always start the cut on the small

side; for U-proﬁ les, never start the cuts on

the open side.

Support long proﬁ le, otherwise the saw

blade can become jammed when the proﬁ le

tips over and the machine can “kick back”.

Material with Mineral Content

(Light building material)

► Only dry cutting is permitted.

► Use vacuum dust extraction. The vacu-

um cleaner must be suitable for masonry

dust.

9 Use of Accessories

The machine has a longitudinal slot at the

base plate underside to take up a guide rail.

With this guide rail, it is made easy to carry

out larger cuts.

PROTOOL Guiding System

For easy and safe handling when cutting

large work pieces as well as for achiev-

ing exact angle cuts, the use of the

GRP 800/1400/3000-2 guiding system is

recommended.

With it, clean cuts are possible by preci-

sion guiding of the machine along a cutting

line. In addition, the hard anodising of the

guide rail makes possible easy gliding of the

machine and thereby reduces the required

advancing force while improving the work

progress.

The saw’s side suction clearance on the bar

is possible to adjust with the adjusting nobs

[6-1].

Mounting the Guide Rail

(GRP 800/1400/3000-2)

The mounting of the guide rail [7-1] takes

place with the use of the special screw

clamps CL-GRP 300 [7-2] which are slid

into the receptacle slots provided (Figure

[7a]). This makes secure holding possible

also on uneven surfaces. In addition, the

“Anti-slip Coating” applied to the underside

of the guide rail ensures secure contact and

prevents scratches on sensitive material

surfaces.

Mounting the Connection Piece

(CN-GRP)

Depending on the application and the size

of the work piece, several guide rails can be

connected together (Figure [7c]) with the

use of the connection piece [7-4]. For the

permanent connection of several guide rails,

the connection pieces can be fastened with

screws at the respective threaded holes.

Mounting the Angle Unit (GRP-AG-2)

The combination of the guide rail and the

continuously adjustable angle unit [7-3]

makes possible exact angle cutting, e. g.,

for ﬁ tting work. The angle unit is mounted

according to Figure [7b]. On the scale, the

required angle can be set.

► When sawing with the PROTOOL GRP

guiding system, 4.5 mm is always to be

added to the necessary cutting depth.

Saw Table

Additional application possibilities are avail-

able with the use of a saw table. Further

information in this regard is available from

your dealer.

10 Maintenance

- The unit should be stored in a dry place

where it is protected against freezing.

WARNING

To verify that the protective insulation

remains intact, the machine must be

subjected to a technical safety test

afterwards. For this reason, this work

must be performed exclusively by a

professional electro-workshop.

- With each changing of the saw blade, re-

move deposited saw dust from the inside

of the protective guard.

- The ventilation slots on the motor casing

should be cleaned out from time to time.

After an operating period of approx. 200

hours, the following maintenance work

must be performed:

- Check the motor brushes and replace if

necessary. Clean the motor housing.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Protool CSP 56 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 11,68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Protool CSP 56 Manual

Product: