Manual Protool CSP 56 (page 18 of 136) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish)

110272

Zoom out

Zoom in

1/136

No-load speed reduction

The electronic control reduces the no-load

speed of the machine which results in re-

duced noise and wear of motor and gear.

Constant speed electronics

The constant speed electronics maintains

the speed between no load and load nearly

constant and ensures uniform feeding which

produces an even cutting edge.

Electronic overload protection

In case that the machine is extremely over-

loaded, an electronic overload protection

protects the motor from damage. In this

case, the motor stops and restarts only af-

ter the feeding pressure is reduced, res.

after relief.

Temperature-dependent overload

protection

To prevent overheating under an extreme

long-term load, the safety electronics switch

the motor into cooling mode when the criti-

cal temperature is reached. The machine

cannot be loaded, and it runs at reduced

RPM. After cooling, the tool is once again

prepared for operation and can be fully

loaded in about 3 – 5 minutes. If the tool

gets hot while running, the heat protection

reacts correspondingly earlier.

Speed pre-selection

With the speed control [1-11], the speed

can be continuously pre-selected:

Speed 1: 2000 min

–1

Speed 4: 3500 min

–1

Speed 2: 2500 min

–1

Speed 5: 4100 min

–1

Speed 3: 3000 min

–1

Speed 6: 4700 min

–1

The required speed depends on the saw blade

used and the material to be worked.

Run-on Brake

After releasing the On/Off switch, the in-

tegrated run-on brake stops the saw blade

within approx. 2 seconds.

7.2 Cutting Depth Adjustment

Loosen the clamping lever [3-1].

Set the required depth on the cutting depth

scale [3-2].

Raise: smaller cutting depth (Figure [3a])

Lower: larger cutting depth (Figure [3b])

Re-tighten the clamping lever [3-1].

To achieve the best cutting results, the saw

blade should protrude from the material by

no more than 3 mm.

7.3 Cutting Angle Adjustment

Loosen the winged screws [4-2].

Set the cutting depth on the scale [4-3] to

the required value (the cutting angle scale

is marked in 1°-steps).

Re-tighten the winged screws [4-2].

WARNING

The maximum cutting depth is reduced

for bevel cuts.

7.4 Cutting Edge Indicator

When making right-angled (90°) and bevel

cuts, the cutting edge indicator [4-1] and

the middle of the saw blade are in one line.

During cutting, the edge of the cut indica-

tor aligns in case of cutting with guide rail

(GRP 800/1400/3000-2), with the saw blade

centre at all cutting angles (from 0° to 45°).

In case of cutting without the guide rail the

cutting indicator edge follows the centre of

the saw blade in square cut only.

Follow your marked line with the cutting

edge indicator.

7.5 Parallel Guide

The parallel guide [1-9] is inserted in the

holders on the foot plate [1-7] and secured

with the winged screws [1-12]. The paral-

lel guide makes possible exact cuts along

a workpiece edge or the cutting of parallel

strips. The maximum cutting width is ap-

prox. 100 mm.

7.6 Exhaustion

CAUTION

Inhaled dust may damage the air pas-

sages.

► Tools should be permanently connected

to the dust exhausting plant.

► Wear respirator if you work with dust.

To exhaust dust, suction adapter [5-1] can

be mounted on the sawdust ejector through

which common exhaust hoses of exhausters

can be connected.

Insert the adapter to the dovetail and

secure with locking – see ﬁ gure [5].

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Protool CSP 56 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 11,68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Protool CSP 56 Manual

Product: