Manual Protector AS-8000 (page 29 of 88) (English, German, Dutch, French)

738854

Zoom out

Zoom in

1/88

PREPARATION

Minimum width of window opening

This is based on:

a) The performance of the exhaust air device in m³/h

b) The size of the window to be opened in m²

c) The size of the window opening in cm

(see table 1)

Most kitchens have rectangular tilt and swivel windows.

If you have windows that are, for example, round, then

please ask the installation technician, heating engineer

or electrician to calculate the minimum opening. The

required minimum opening for the rectangular window

can be found in the table for tilt and swivel windows as

an example.

1. Determine the exhaust air capacity of your exhaust air

device in m

/h. You can ﬁnd the exhaust air capacity

on the type plate or in the operating instructions for

your exhaust air device (e.g. extractor hood).

2. Measure the inside width and height of the window

and calculate the window size in m².

(Width x height = m²);

e.g. (0.8 m x 1.0 m = 0.8m²) = window size

3. Determine the opening size (minimum opening of your

window) from your exhaust air capacity and window

size using the table.

4. Measure the upper inside window opening gap in cm

when tilted. The gap size on your window may not be

less than the determined opening size! A larger gap or

window opening is advantageous.

5. If the gap size for the window is less than the permitted

value for the window opening in accordance with the

table, then the window may only be able to achieve the

necessary opening when opened on swivel. A minimum

gap size must also be achieved in the swivel position. The

window transmitter must be attached in such a way that

the minimum gap size is ensured. We recommend ﬁxing

the minimum gap size with the help of a distance piece.

Attaching the window transmitter

AS-F20 (ﬁgure 9)

NOTE

Attach the window transmitter and the magnet to

the window and the frame for the initial operation

using double-sided sticky tape. Once the function

test has been completed then the window

transmitter and the magnet can be screwed in place.

This section describes attachment of the window

transmitter for a tip and swivel window.

a) Attachment for the tilt position

The window transmitter and the magnet must be

attached as shown in ﬁgure 2 TILT POSITION. The

window transmitter must be attached near the hinge

for the swivel position. The attachment point must be

selected in such a way that a ‘window open’ signal is

only produced once the necessary opening is achieved

in accordance with the table.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Protector AS-8000 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Protector AS-8000 Manual

Product: