Manual Protector AS-8000 (page 30 of 88) (English, German, Dutch, French)

738854

Zoom out

Zoom in

1/88

b) Attachment for swivel position

The window transmitter and the magnet must be

attached as shown in ﬁgure 2 SWIVEL POSITION. The

window transmitter must be attached near the hinge for

the tilt position. The attachment point must be selected

in such a way that a ‘window open’ signal is only

produced once the necessary opening is achieved in

accordance with the table.

Proceed as follows to attach the window transmitter:

1. Attach the lower casing section of the window

transmitter at the correct position using the included

double-sided sticky pad.

Alternatively there is a prepared hole in the lower

casing section to screw the window transmitter onto

the window frame. To use this carefully remove the

printed circuit board from the lower casing section and

screw the casing in place using the included screw.

Then carefully replace the printed circuit board.

2. Insert the battery (1x size CR2477) into the

transmitter with the correct polarity and ﬁx it in place.

NOTE

Please ensure that you lay the battery in the

window transmitter on top of the metal tab and

not below it.

3. Press the upper casing section onto the lower

casing section.

Attaching the magnet

Fix the magnet in place in accordance with ﬁgure 1.

Open and close the window once after attachment.

The transmitter should ﬂash at least once for each

activation. Proceed as follows to attach the magnet:

1. Fix the lower magnet casing section at the correct

position using the included double-sided sticky pad.

2. Insert the magnet and check the function of the

window transmitter.

CAUTION!

The distance between the window transmitter and

the magnet may not be more than 7 mm

3. Open the window again. The green LED (OPEN) should

ﬂash brieﬂy if the transmitter is installed correctly.

4. Now close the window. The red LED (CLOSED) should

ﬂash brieﬂy.

5. Once all the functions have been tested successfully

the transmitter and the receiver must be screwed to the

window/window frame. There is a prepared hole for

this purpose on the lower casing section of the window

transmitter and in the lower magnet casing section.

These can be used to screw the window transmitter

and the magnet to the window/window frame. This

prevents the window transmitter and the magnet from

falling down unintentionally.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Protector AS-8000 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Protector AS-8000 Manual

Product: