Manual Protector AS-7000 (page 31 of 88) (English, German, Dutch, French)

738868

Zoom out

Zoom in

1/88

distance between the two sections of the casing is

less than 6 mm when the window is closed. Use

the included packing (U) to adjust the parts for

this purpose.

• We recommend attaching the contact and the magnet

with the double-sided sticky tape before the ﬁnal

mounting and to only screw the elements in place at

the end.

Testing the function of the window tilt

and swivel position

• Slowly move the window to the tilt or swivel position,

then the green LED on the window transmitter (OPEN)

will ﬂash brieﬂy before the maximum tilt or

swivel position.

• Close the window, then the red LED (CLOSED) will

ﬂash brieﬂy.

• Finally check the opening gaps again using the

minimum value determined in accordance with Table 1.

Attaching the roller shutter transmitter

AS-R40 (ﬁgures 20 and 26)

NOTE

Attach the roller shutter transmitter and the

magnet to the window and the frame for the initial

operation using double-sided sticky tape. Once the

function test has been completed then the roller

shutter transmitter and the magnet can be

screwed in place

Attaching the roller shutter transmitter

The roller shutter transmitter and the magnet must

be attached as shown in ﬁgure 4. The roller shutter

transmitter must be attached to the inside of the

window in the vicinity of the opened roller shutter.

Alternatively the transmitter may also be attached

between the window and the roller shutter but this

will weaken the radio signal. The attachment point

must be selected in such a way that a ‘roller shutter

open’ signal is only produced once the roller shutter

is completely open.

Proceed as follows to attach the roller

shutter transmitter:

1. Mount the lower casing section of the roller shutter

transmitter to the correct position using the included

double-sided sticky pad.

Alternatively there is a prepared hole in the lower casing

section to screw the roller shutter transmitter onto the

window frame. To use this carefully remove the printed

circuit board from the lower casing section and screw

the casing in place using the included screw. Then

carefully replace the printed circuit board.

2. Insert the battery (1x size CR2477) into the

transmitter with the correct polarity and ﬁx it in place.

AS 7000_1.Vers. 2017 Manual 3xAA@150x180.indd 31 07.06.17 18:37

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Protector AS-7000 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,91 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Protector AS-7000 Manual

Product: