Manual Prophete 0516 (page 21 of 32) (English, German, Dutch, French, Italian)

519093

Zoom out

Zoom in

1/32

BICYCLE

COMPUTER

Article no. 0516

15 functions

OPERATING INSTRUCTIONS

5.2 Setting the wheel size

After inserting new batteries (7.1). New start or change the wheel size.

Determining the wheel size:Mark the front wheel and the ground at the same

point, or use the valve as orientation. Move the wheel one wheel revolution

forwards and measure the covered distance in mm. This is your entry value.

Basic setting display: 2124 (

mm), The ones digit 4 ﬂ ashes. Press the RIGHT

key: The ones digit is increased by one.

For all settings: Keep the RIGHT key pressed down – the respective numbers

will progress faster. Conﬁ rm your selection by pressing the LEFT key. The

tens digit now ﬂ ashes. Press the RIGHT key: The tens digit is increased by

one. Please set the following digits in the same manner. The thousands digit

can only be set from 0 to 5. Finally, press the LEFT key once more to conﬁ rm

the setting.

5.3 Selecting KM/H Miles

The choice of the unit of measurement comes directly after entering the

wheel size. Press the RIGHT key to choose between KILOMETRE (KM) and

MILES (M) and conﬁ rm with the LEFT key. The system then switches to the

mode to set the inspection interval.

5.4 Setting the inspection interval

The display 600 KM ﬂ ashes. This function permits you to set the kilometres

until the next bicycle inspection. Pressing the RIGHT key lets you make set-

tings of 200/400/600 or 800 kilometres. Use the LEFT key to conﬁ rm the set

value. After the kilometres you set have been reached, a spanner symbol will

appear in the display to remind you of your bicycle inspection. Press the

RIGHT key to switch oﬀ this notice. After setting the inspection interval,

the display will switch to the mode for setting the time.

5.5 Setting the 12/24-hour display

Press and hold the LEFT key and the 24-hour display ﬂ ashes. With the RIGHT

key, choose between the 12-hour and 24-hour display of the CLOCK and

conﬁ rm with the LEFT key.

5.6 Setting the clock

Immediately after choosing the 12/24-hour display you will be able to set

the time. The hours display ﬂ ashes. Press the RIGHT key: The hours display

is increased by one. Press the LEFT key: The minutes display ﬂ ashes. Press

the RIGHT key: The minutes display is increased by one. Press the LEFT key

to conﬁ rm the time entry. The settings are now completed and the bicycle

computer is ready for use.

5.7 Bicycle computer check

To check if the bicycle computer and sensor were installed correctly, press

the LEFT key to activate the display. Place the computer in the computer

mount and turn the front wheel of your bicycle and the speed will be indicated.

5.8 New start/Reset

To reset entered and stored data, press both the LEFT and RIGHT keys at

the same time for approx. 3 seconds. All settings will have to be re-entered

after the new start/reset. (see Point 5.2 Setting the wheel size – 5.6 Setting

the clock).

5.9 Automatic start/stop

Each time before the bicycle computer is used (display is blank), it must be

switched on by pressing a key. When you start oﬀ , all measurements begin

automatically until the bicycle stops. When you continue your ride, the meas-

urements continue. The bicycle computer switches oﬀ automatically to save

the battery after the bicycle has stopped moving for more than 5 minutes.

6. Modes/Functions

After starting up the bicycle computer, the display will show the speed and

the time.

Speed Is continuously calculated and updated and is ALWAYS displayed at

the top right. Measuring range: 0,1 – 99,9

Press the RIGHT key to switch between the following modes:

•

ODO (total kilometres)

All travelled kilometres (miles) will be stored. Maximum memory area:

9999,9

•

DST (trip distance)

Automatic start when bicycle trip begins. Maximum measuring range

999.9

•

MXS (maximum speed)

The maximum achieved speed is stored. Maximum measuring range: 99,9

•

AVS (average speed)

Maximum measuring range: 99,9

•

TM (trip time/trip chronometer)

Automatic start when bicycle trip begins. Maximum measuring range:

9 hrs 59 min 59 sec

•

Temperature

Press and hold the LEFT key in the temperature mode:

C (Celsius) ﬂ ashes, use the RIGHT key to now switch to

F (Fahrenheit).

Conﬁ rm the desired setting with the LEFT key.

•

SCAN (scan function)

Rolling display of functions: Continue pressing the RIGHT key until

you reach the SCAN mode. SCAN appears in the display. In this mode,

the functions (DST, MXS, AVS, TM) will be displayed automatically at

4-second intervals in succession.

•

One-time scanning quick run-through

If you keep the RIGHT key pressed for approx. 2 seconds, a one-time

scanning quick run-through occurs.

•

Time

Speed tendency and comparison is always displayed during the trip.

•

Speed tendency

Presentation of current speed: The wheels of the bicycle symbol rotate

faster or slower.

•

Speed comparison

On the right next to the speed display you will see "+" or "-".

This indicates that you are riding faster or slower than the previously

travelled average speed. (AVS)

•

Instantaneous memory

The bicycle computer has a unique instantaneous memory that can

record the values for trip distance (DST), average speed (AVS) and trip

time (TM) at the end of the driven distance. Press the LEFT key at the end

of a stage. The values for DST, AVS and TM are stored and can be re-

viewed at a later period. You can view the saved values by repeatedly

pressing the RIGHT key. To exit this mode, press the LEFT key. The in-

stantaneous memory is suitable for, e.g. capturing data after a race to

quickly save the values after crossing the ﬁ nish line.

6.1 Resetting the route data (DST, TM, AVS) to zero

Press the RIGHT key to display (DST) and keep the LEFT key pressed for

approx. 3 seconds. The three route data (trip distance counter – DST,

trip time – TM, average speed – AVS) will be reset to zero.

6.2 Resetting the maximum speed (MXS) to zero

Press the RIGHT key repeatedly until the maximum speed (MXS)

is displayed

and hold down the LEFT key for 3 seconds. The maximum speed (MXS) is

reset to zero.

6.3 Manual entry of total kilometres

To enter the total kilometres (ODO) after battery replacement or new start/re-

set, all of the settings from Point 5.2 Setting the wheel size to Point 5.6 Setting

the clock must be entered again.

Then press the RIGHT key until you reach the mode (ODO). Now keep the

LEFT key pressed down for approx. 3 seconds, the last digit of the total kilo-

metres begins to ﬂ ash. Press the RIGHT key to set the number and conﬁ rm

the entry by pressing the LEFT key. Then select the next digit for the entry.

Repeat the procedure until the desired value for the total kilometre counter

has been set. Press the LEFT key again to return to the normal (ODO) mode.

7. Battery replacement

7.1 Bicycle computer

Use a coin to unscrew the battery compartment lid at the back of the bicycle

computer. Insert the 3 V battery so that the positive pole (+) is visible.

Replace the lid and screw shut. After the batteries have been inserted,

all settings must be re-entered (see Point 5.2 Setting the wheel size).

8. Declaration of Conformity

R&TTE 2004/108/EC

Short texts of declaration of conformity: Prophete GmbH & Co. KG here-

with declares that the bicycle computer (Art. No.: 0516) conforms to the

fundamental requirements and the remaining relevant provisions of the

2004/108/EC guideline.

9. Description of fault

If a fault occurs, ﬁ rst check the following points before submitting the bicycle

computer for complaint.

No speed indication

•

Check for correct magnet/sensor alignment.

•

Check the batteries.

•

If the battery is too weak, there will be no display.

Incorrect speed measurement or speed display at standstill, or high incorrect

maximum speed display

•

Check if the wheel size was set correctly.

•

Check if the correct KM/Miles setting is selected.

•

Check if the magnet and sensor are positioned correctly.

•

RF (radio frequency) interference from a chest strap. Do not get too close

to the bicycle computer with a chest strap, as the speed indicator will begin

to "run".

•

Unknown atmospheric or RF disturbances, atmospheric or radio inter-

ference, high-voltage lines, railroad lines, etc. can also cause an

incorrect speed display.

Display is black

Too high temperature, or display is exposed to direct sunlight, will return to

normal after cooling oﬀ .

Display shows erratic numbers

Remove the bicycle computer battery and reinsert.

No display

•

Check the battery

•

Is the battery inserted correctly? Observe +/-.

10. Warranty provisions

SI-Zweirad bicycle computer Art. No.: 0516

This bicycle computer has a 2-year warranty. Warranty begins as of the pur-

chase date (receipt, proof of purchase). During the warranty period, com-

plaints about defective bicycle computers can be made with your distributor,

or at the service address speciﬁ ed below. During this period we will correct

free of charge all defects that can be attributed to material defects or mal-

functions. Excepted from the warranty are batteries, improper handling, falls,

impacts and the like. A new warranty period does not begin after repairs or

replacement of the device. The warranty period of 2 years as of date of pur-

chase remains deﬁ nitive.

Please send your carefully packaged bicycle computer with your receipt to

the following address:

Prophete GmbH u. Co. KG

Lindenstrasse 50

D-33378 Rheda-Wiedenbrück, Germany

Phone: 05242-4108-59

Fax: 05242-4108-73

E-mail address: service@prophete.net

Home page: www.prophete.de

C = Distance in millimetres per rotation

BA_Fahrrad_PC_0516_GB.indd 1-8 25.05.2009 13:24:35 Uhr

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Prophete 0516 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 6,7 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Prophete 0516 Manual

Product: