Manual Practixx PX-RRM-600WI (page 37 of 68) (English, German, French)

782000

Zoom out

Zoom in

1/68

GB | 29

The customer‘s mains connection as well as the ex-

tension cable used must also comply with these reg-

ulations.

Damaged electrical connection cable

The insulation on electrical connection cables is often

damaged.

This may have the following causes:

• Pressure points, where connection cables are

passed through windows or doors.

• Kinks where the connection cable has been improp-

erly fastened or routed.

• Places where the connection cables have been cut

due to being driven over.

• Insulation damage due to being ripped out of the

wall outlet.

• Cracks due to the insulation ageing.

Such damaged electrical connection cables must not

be used and are life-threatening due to the insulation

damage.

Check the electrical connection cables for damage

regularly. Ensure that the connection cables are dis-

connected from electrical power when checking for

damage.

Electrical connection cables must comply with the ap-

plicable VDE and DIN provisions.

Only use connection cables of the same designation.

The printing of the type designation on the connection

cable is mandatory.

9.1. Quick start (Fig. 19/20)

After installing the boundary wire (11), you can use the

robot mower (1).

Adjusting the cutting height

• Turn the cutting height adjustment knob (2) clock-

wise to increase the cutting height seamlessly be-

tween 20 - 60 mm.

• Turn the cutting height adjustment knob (2) an-

ti-clockwise to decrease the cutting height seam-

lessly between 20 - 60 mm.

m NOTE

The arrow on the cutting height adjustment knob (2)

points to numbers outside the knob. Here you can

read o󰀨 the cutting height currently set in 5 mm steps.

Halting/stopping the robot mower:

• To stop the robot mower, press the stop button (4).

• The robot mower stops immediately and the blade

disc (6) stops.

•

Flashes

red

The boundary

wire is damaged

or not connected

properly.

Check that both

ends of the bounda-

ry wire are con-

nected and that

the cable clamp is

reliable.

Check that the

boundary wire has

not been broken.

8.5. Before commissioning

• Set the cutting height to the maximum cutting

height (60 mm) using the cutting height adjustment

knob (2) as shown in gure 18.

• Place the mower in the working area and start it (as

described in point 9).

• Observe the mower for some time.

• If it returns to the charging station (10) without any

problems, the installation is complete.

TIP:

Before rst use:

Position the mower, directly behind the charging sta-

tion (10), at a 90° angle to the boundary wire (11) and

give it the command to return to the charging station

(10) via the “HOME” button (see point 9).

The mower will now drive back to the charging station

(10) along the complete boundary wire (11) (Fig. 2)

This allows you to identify problem areas immediately

before rst use and correct them if necessary.

The same procedure is recommended for critical

places, such as embankments/ditches/beds, etc.

Proceed as described above and start the mower

(see point 9) with the “START” button.

In the event of a problem, you can stop the mower by

pressing the stop button (4) on the product.

9. Starting up / adjustments

m ATTENTION!

To ensure optimum function, a software update

must be carried out before rst use. (see 13.3

Software update)

m NOTE

For a long service life, the robot mower (1) should only

be operated at an outdoor temperature of 5 - 40 °C.

m ATTENTION!

Always make sure the product is fully assembled

before commissioning!

Electrical connection

The electrical motor installed is connected and ready

for operation. The connection complies with the appli-

cable VDE and DIN provisions.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Practixx PX-RRM-600WI in the language / languages: English, German, French as an attachment in your email.

The manual is 6.65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Practixx PX-RRM-600WI Manual

Product: