582079
10
Zoom out
Zoom in
Previous page
1/20
Next page
POWXQG4060 EN
Copyright © 2014 VARO P a g e | 10 www.varo.com
WARNING: Never start or operate the saw unless the bar and chain are
properly installed.
Fill the fuel tank (A) with correct fuel mixture.
Fill the oil tank (B) with correct chain and bar oil...
9.2 Starting a cold engine
Activate the chain brake (move the hand guard forward and engage it) (Fig 9a)
To start the saw, push the switch (ON/OFF switch) to the ON (I) position. (Fig. 9b)
Pull out the choke (A) to the point where it latches in place. (Fig. 9c)
Press primer bulb 3 to 5 times.
Place the saw on a firm and level surface. Hold the saw securely with your foot as
illustrated. Pull the starter several times until first firing sound is heard. (Fig. 9d)
You wont have to use any force to start this engine because of the “easy
start” system.
Choke will be turned off automatically when you pull the throttle. (Fig. 9e)
Forcefully pull the starter until the motor engages. (Fig 9f)
Slightly press in the throttle (Fig 9g)
Pull back the brake lever to release the chain brake (Fig 9h)
9.3 Warm start
Activate the chain brake (Fig 9i)
Set the switch (on/off) to ON(I) position (Fig 9j)
Forcefully pull the starter until the motor engages (Fig 9k)
Slightly press down on the throttle (Fig 9l)
Release the chain brake (Fig 9m)
9.4 When engine is saturated with fuel
Remove the air filter
Remove the spark plug
Position the machine in an angle of 45° with the sword upwards
Pull the starters rope a few times
Clean the spark plug and place back
Place back the air filter and start without choke
9.5 To stop engine (Fig 9n)
Release trigger and allow engine to return to idle speed.
Push the I/O (on/off) switch to O (off) to stop engine.
Note: for emergency stopping, simply activate chain brake and switch the
I/O (on/off) switch to o (off).
9.6 Chain brake operational test
Test the chain brake periodically to ensure proper function.
Perform a chain brake test prior to initial cutting, following extensive cutting, and definitely
following any chain brake service.
Test chain brake as follows:
Place saw on a clear, firm, flat surface.
Start engine.
Grasp the rear handle (A) with your right hand (fig. 10).
With your left hand, hold the front handle (B) [not chain brake lever (C)] firmly (fig. 10).
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWXQG4060 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWXQG4060 in the language / languages: English as an attachment in your email.

The manual is 0,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWXQG4060

Powerplus POWXQG4060 User Manual - German - 23 pages

Powerplus POWXQG4060 User Manual - Dutch - 22 pages

Powerplus POWXQG4060 User Manual - French - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info