582079
11
Zoom out
Zoom in
Previous page
1/20
Next page
POWXQG4060 EN
Copyright © 2014 VARO P a g e | 11 www.varo.com
Squeeze the throttle trigger to 1/3 throttle, then immediately activate the chain brake lever
(C) (fig. 10).
Warning: activate the chain brake slowly and deliberately. Keep the chain
from touching anything; don t let the saw tip forward.
Chain should stop abruptly. When it does, immediately release the throttle trigger.
Warning: if chain does not stop, turn engine off and take your unit to the
nearest authorized service center for service.
If chain brake functions properly, turn the engine off and return the chain brake to the
disengaged position.
9.7 Saw chain / bar lubrication
Adequate lubrication of the saw chain is essential at all times to minimize friction with the
guide bar. Never starve the bar and chain of oil. Running the saw with too little oil will
decrease cutting efficiency, shorten saw chain life, cause rapid dulling of chain, and cause
excessive wear of bar from overheating. Too little oil is evidenced by smoke, bar discoloration
or pitch build-up.
Note: saw chain stretches during use, particularly when it is new, and it will
occasionally be necessary to adjust and tighten it. New chain will require
adjustment after about 5 minutes of operation.
9.8 Automatic oiler
Your chain saw is equipped with an automatic clutch driven oiler system. The oiler
automatically delivers the proper amount of oil to the bar and chain. As the engine speed
increases, so does the oil flow to the bar pad.
Do not adjust the chain lubrication system unless the motor has been
turned off.
The chain lubrication system has been preset to medium oil flow at the factory. The flow can
be adjusted if necessary.
To adjust the oil flow, turn the adjusting screw at the bottom side of the housing (Fig 11)
(19)
Turning it clockwise reduces the oil flow, while turning it counterclockwise increases the oil.
9.9 General cutting instructions
9.9.1 Felling
Felling is the term for cutting down a tree. Small trees up to 6-7 inches (15-18cm) in diameter
are usually cut in a single cut. Larger trees require notch cuts. Notch cuts determine the
direction the tree will fall.
Felling a tree:
Warning: a retreat path (A) should be planned and cleared as necessary
before cuts are started. The retreat path should extend back and diagonally
to the rear of the expected line of fall, as illustrated in fig. 12a
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWXQG4060 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWXQG4060 in the language / languages: English as an attachment in your email.

The manual is 0,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWXQG4060

Powerplus POWXQG4060 User Manual - German - 23 pages

Powerplus POWXQG4060 User Manual - Dutch - 22 pages

Powerplus POWXQG4060 User Manual - French - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info