582079
8
Zoom out
Zoom in
Previous page
1/20
Next page
POWXQG4060 EN
Copyright © 2014 VARO P a g e | 8 www.varo.com
7.3.4 To adjust saw chain:
Hold nose of guide bar up and turn adjustment screw (16) clockwise to increase chain
tension. Turning screw counterclockwise will decrease amount of tension on chain. Ensure
the chain fits snugly all the way around the guide bar. (fig 5)
After making adjustment, and while still holding nose of bar in the uppermost position,
tighten the bar retaining nuts securely. Chain has proper tension when it has a snug fit all
around and can be pulled around by gloved hand.
Note: if chain is difficult to rotate on guide bar or if it binds, too much
tension has been applied. This requires minor adjustment as follows:
Loosen the bar retaining nuts so they are finger tight. Decrease tension by turning the bar
adjustment screw counterclockwise slowly. Move chain back and forth on bar. Continue to
adjust until chain rotates freely, but fits snugly. Increase tension by turning bar adjustment
screw clockwise.
When saw chain has proper tension, hold nose of bar in the uppermost position and
tighten the 2 bar retaining nuts securely.
Caution: a new saw chain stretches, requiring adjustment after as few as 5
cuts. This is normal with a new chain, and the interval between future
adjustments will lengthen quickly.
Caution: if saw chain is too loose or too tight, the sprocket, bar, chain, and
crankshaft bearings will wear more rapidly. Study fig.6 for information
concerning correct cold tension (A), correct warm tension (B), and as a
guide for when saw chain needs adjustment (C).
7.3.5 Chain brake mechanical test
Your chain saw is equipped with a chain brake that reduces possibility of injury due to
kickback. The brake is activated if pressure is applied against brake lever when, as in the
event of kickback, operator’s hand strikes the lever. When the brake is actuated, chain
movement stops abruptly.
Warning: the purpose of the chain brake is to reduce the possibility of
injury due to kickback; however, it cannot provide the intended measure of
protection if the saw is operated carelessly. Always test the chain brake
before using your saw and periodically while on the job.
7.3.6 To test chain brake:
The chain brake is disengaged (chain can move) when brake lever is pulled back and
locked. Be sure the chain brake latch is in the off position. (fig. 7a)
The chain brake is engaged (chain is stopped) when brake lever is in forward position and
the chain brake latch is in the on position. You should not be able to move chain. (fig. 7b)
Note: the brake lever should snap into both positions. If strong resistance
is felt, or lever does not move into either position, do not use your saw.
Take it immediately to a professional service center for repair.
Don’t let your motor run in high speed when your chainbrake is activated.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWXQG4060 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWXQG4060 in the language / languages: English as an attachment in your email.

The manual is 0,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWXQG4060

Powerplus POWXQG4060 User Manual - German - 23 pages

Powerplus POWXQG4060 User Manual - Dutch - 22 pages

Powerplus POWXQG4060 User Manual - French - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info