481024
8
Zoom out
Zoom in
Previous page
1/12
Next page
POWXQ5390 EN
Copyright © 2015 VARO P a g e | 8 www.varo.com
The part of the work piece to be sawn off must be able to move freely. It may not be held
or clamped, and no length stop may be used in this regard. It could wedge against the
cut-off wheel and pose a risk of accident.
When using this device keep your fingers a safe distance from the cutting area.
9.3 Never saw with an unsupported hand
Never cut more than one work piece at a time.
Only remove filings, waste and work pieces when the machine has come to a complete
stop.
Never touch the cut material until it has cooled down. Risk of burns!
9.4 Operation:
Always observe the safety warnings and applicable regulations.
Before beginning to saw, ensure that the cut-off wheel protective hood is in the correct
position.
Start the cut-off saw by pressing switch (A) on the inside of the D-handle.
You must wait until the cut-off wheel has achieved the maximum number of revolutions
before using the saw.
Slowly and evenly push the saw head downward on the D-handle.
After sawing you must bring the saw head back to the starting position.
Use the switch to power the saw off.
Always wait until the cut-off wheel has come to a complete stop before switching on the
device again or making adjustments.
Always check the condition of the cut-off wheel before doing any work with
this device. Only work with a flawless cut-off wheel!
Never let other people stand behind the saw or close to the work piece, as
there is a risk of waste material being thrown out.
Flying sparks from the cutting work may cause injuries and ignite
flammable materials.
10 SET-UP AND ADJUSTMENTS
10.1 Cut-off wheel assembly (Fig. 6)
Only replace the cut-off wheel after first removing the plug from the mains!
The cut-off wheel must conform to the stated technical specifications.
Check it for flaws before installation (cracks, warping). Do not use flawed cut-off wheels.
Open cut-off wheel guard (E).
Press spindle lock button (C) and unscrew wheel clamp screw (W) using the key
provided.
Remove the screw, washer (V), clamping flange (U) and the cut-off wheel (F). (Fig. 7)
Perform this process in reverse to install the new wheel. Do not over-tighten the screw.
All guards must be in place and the wheel must be able to turn freely.
Set the cutting-depth stop (see section 10.2).
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWXQ5390 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWXQ5390 in the language / languages: English as an attachment in your email.

The manual is 0,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWXQ5390

Powerplus POWXQ5390 User Manual - German - 13 pages

Powerplus POWXQ5390 User Manual - Dutch - 15 pages

Powerplus POWXQ5390 User Manual - French - 13 pages

Powerplus POWXQ5390 Additional guide - All languages - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info