481024
7
Zoom out
Zoom in
Previous page
1/12
Next page
POWXQ5390 EN
Copyright © 2015 VARO P a g e | 7 www.varo.com
medical implants consult their doctor and the manufacturers of the implants before
operating this device.
8 TRANSPORT AND START OF OPERATION
8.1 Transport and set-up
The machine must be set up indoors. Upon installation, the workplace must provide
satisfactory conditions for the proper performance of technical work.
The installation surface must be sufficiently level and load-bearing. If required, the
machine can be fastened down to the installation surface.
Due to packaging technical reasons the machine comes not fully assembled.
8.2 Assembly
If you discover transport damage while unpacking the machine inform your dealer
immediately. Do not use the device!
Please dispose of the packaging in an environmentally-friendly way.
Remove the anti-corrosive grease from the saw table using a mild solvent.
8.3 Assembly of clamping jig handle (J) (Fig. 2)
8.4 Release of the saw head
The machine comes fitted with a locked saw head as standard. The lock bolt of the saw head
(Q) can be removed. Let the saw head slide slowly upward. (Fig. 3)
When transporting the machine the saw head must be locked in place again.
8.5 Key storage
Put the supplied key (T) in the holder on the rear of the saw. (Fig. 4)
8.6 Electrical connection
The mains power supply and the extension cable used must meet the stipulated
regulations.
The mains supply and the frequency must agree with the data provided on the machine
rating plate.
The device must be protected by a 10 A fuse.
Only use a mains cable with the designation H07RN-F.
Connections and repair of electrical equipment may only be carried out by qualified
electricians.
8.7 Start of operation
Press switch (A) on D-handle (B) to start the device: As soon as you release the switch the
machine will shut off.
9 OPERATING THE MACHINE
9.1 Correct working position:
Stand in front of the machine in the direction of the cut.
9.2 Handling the work piece:
The work piece to be cut must be firmly held in the clamping jig, so that it cannot move
during the cutting process.
Always secure the work piece between angle plate (G) and clamping jig pressure plate
(H). ( Fig. 5)
Do not cut undersized work pieces.
Support long work pieces with roller blocks.
Large, round or irregularly shaped work pieces must have additional clamping
arrangements. Use G-clamps and blocks to firmly hold the work piece in place.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWXQ5390 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWXQ5390 in the language / languages: English as an attachment in your email.

The manual is 0,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWXQ5390

Powerplus POWXQ5390 User Manual - German - 13 pages

Powerplus POWXQ5390 User Manual - Dutch - 15 pages

Powerplus POWXQ5390 User Manual - French - 13 pages

Powerplus POWXQ5390 Additional guide - All languages - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info