Manual Powerplus POWXQ5390 (page 6 of 12) (English)

481024

Zoom out

Zoom in

1/12

POWXQ5390 EN

 Stopping the spinning cut-off wheel by lateral pressure is not allowed.

 The work piece to be cut must be firmly held in the clamping jig, so that it cannot move

during the cutting process.

 Do not cut undersized work pieces.

 Support long work pieces with roller blocks.

 Large, round or irregularly shaped work pieces must have additional clamping

arrangements. Use G-clamps and blocks to firmly hold the work piece in place.

 The part of the work piece to be sawn off must be able to move freely. It may not be held

or clamped, and no length stop may be used in this regard. It could wedge against the

cut-off wheel and pose a risk of accident.

 When using this device keep your fingers a safe distance from the cutting area.

 Never saw with an unsupported hand.

 Never cut more than one work piece at a time.

 For safety reasons always operate this device using two hands. Do not use this machine

if standing on a step/platform.

 Always wait until the cut-off wheel has come to a complete stop before switching on the

device again or making adjustments.

 Never touch the cut material until it has cooled down. – Risk of burns!

 Always keep the motor ventilation slots clear and clean.

 Set up the machine so that there is enough operating room and room to guide the work

piece.

 Never let other people stand behind the saw or close to the work piece, as there is a risk

of waste material being thrown out.

 You must wait until the cut-off wheel has achieved the maximum number of revolutions

before using the saw.

 Flying sparks from the cutting work may cause injuries and ignite flammable materials.

 Never put your hands in the running machine when guiding or removing a work piece.

 You must comply with the stated maximum and minimum dimensions of work pieces.

 Only remove filings, waste and work pieces when the machine has come to a complete

stop.

 The motor will automatically shut off if overloaded. After a cooling down period of around

5 minutes the thermal circuit breaker will allow resumption of operation.

 Only use cut-off wheels dimensioned for 3,500 rpm or higher.

 Never use a circular saw blade or other toothed saw blades in the machine.

 Replace worn or damaged cut-off wheels at once.

7 RESIDUAL RISKS

 Even during approved operation of this device the following residual risks exist:

 Risk of injury by the freely running cut-off wheel in the workplace.

 Danger from a fractured cut-off wheel.

 Injury from ejected/emitted waste, work pieces, noise and dust. Always wear personal

safety equipment such as safety goggles, ear protection and dust mask.

 Dust and many fumes generated when cutting may pose a health hazard. In order to limit

health risks, always work in a well-ventilated area or room.

 Risk of electric shock due to non-approved cabling. Avoid making contact with earthed

devices such as pipes, radiators, stoves etc.

 Lung damage from failure to wear a suitable dust mask.

 Damage to hearing due to failure to wear appropriate ear protection.

 Health problems resulting from hand-arm vibrations if using the device for a long period of

time or if the device is not properly controlled and maintained.

 Warning! This power tool generates an electro-magnetic field during operation. Under

certain circumstances, this field may interfere with active or passive medical implants. In

order to reduce the risk of serious or fatal injuries, we recommend that persons with

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWXQ5390 in the language / languages: English as an attachment in your email.

The manual is 0,43 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWXQ5390

Powerplus POWXQ5390 User Manual - German - 13 pages

Powerplus POWXQ5390 User Manual - Dutch - 15 pages

Powerplus POWXQ5390 User Manual - French - 13 pages

Powerplus POWXQ5390 Additional guide - All languages - 3 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Powerplus POWXQ5390 Manual

Product: