481023
7
Zoom out
Zoom in
Previous page
1/11
Next page
POWXQ5320 EN
Copyright © 2011 VARO Page | 7 www.varo.com
7 ADJUSTMENTS
ATTENTION! Disconnect the power plug before carrying out any
adjustments or maintenance.
7.1 Assembling the stand (Fig. 4)
The support brackets and stand legs have corresponding letters for easy assembly.
Tools needed: Adjustable wrench or 13 mm wrenches and philips.
§ Insert stand legs, labeled “A”, into end tubes of the support bracket labeled “A”. Angled
ends of stand legs should face away from each other so they resemble a “V”. Align holes
for hardware. Repeat with second support bracket and legs labeled “B”.
§ Fit leg assemblies into braces. Leg assembly “B” rests on inside of braces. Leg assembly
“A” rests on the outer side. Line up holes in the braces and legs. Install hardware through
holes.
§ Using wrench, tighten hardware.
§ Place stand on level ground and line up grooves under tile saw with brackets on stand.
Position table onto stand.
§ Be sure the tile saw is on level ground and the stand is sturdy before use.
7.2 Installing the splash Hood (Fig. 6-7)
§ Remove bevel table
§ Install the L-shaped splash hood bracket into the lip located under the table behind the
wheel.
§ Install the washers and screw into table and through splash hood bracket then tighten
securely.
Note: be sure that hood bracket is aligned with cutting wheel so that it
does not interfere with material being cut.
§ Align splash hood with wheel and slide over bracket. Line up through holes in splash hood
with slot in splash hood bracket
Note: always adjust splash hood horizontally to table and slightly above tile
thickness. Hood should not be touching tile.
§ Install hex bolt through hood and bracket. Thread knob onto bolt and tighten to desired
height.
§ Replace bevel table
7.3 Installing the overflow drain (fig. 8)
§ Remove bevel table (16)
§ Locate hole on bottom of water fill reservoir
§ Push overflow drain into hole firmly
§ Replace bevel table
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWXQ5320 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWXQ5320 in the language / languages: English as an attachment in your email.

The manual is 0,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWXQ5320

Powerplus POWXQ5320 User Manual - German - 12 pages

Powerplus POWXQ5320 User Manual - Dutch, French - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info