582379
7
Zoom out
Zoom in
Previous page
1/12
Next page
POWX242 EN
Copyright © 2015 VARO p a g e | 7 www.varo.com
8 ADDITIONAL SAFETY INSTRUCTIONS FOR BATTERIES
When replacing batteries, always replace the complete set. Do not mix old batteries with
new ones.
Prevent removed batteries from short circuiting.
Do not store batteries where the temperature may rise above 50 °C, e.g. in a car which
has been parked in the sun.
Do not burn batteries.
Never attempt to open batteries.
In case of battery leakage, carefully remove the liquid using a cloth. Avoid skin or eye
contact. Do not swallow. In case of skin or eye contact, rinse abundantly for 10 minutes
with clean water and consult a physician.
9 ASSEMBLY
9.1 Installing the stand (Fig.2-4)
Fasten the feet (13) to the base frame (12) with the screws (19).
Turn the base frame upright (see Fig. 5).
PIace the water reservoir (3) in the base frame (12).
Place the cooling water pump (13) in the water reservoir (3).
Fill with water until the pump (13) is full.
Place the complete tile cutting machine in water reservoir (3) (see Fig. 2).
Unscrew the star grip screw (11) (for securing during transportation!).
9.2 Installation of the pump. (fig 3)
Never let the pump run dry. Always make sure that the suction opening is
fully immersed.
10 OPERATION
Remove the head lock knob before use.
Adjust the required tool position, then tighten all the adjusting knobs, fence bolts and mitre
gauge bolts.
Before switching the machine on, make sure that the water pump is immersed.
Turn on the main switch and allow your tool to reach the maximum speed before commencing
cutting.
Place the workpiece against the fence or mitre fence.
Keep the workpiece in place and slowly guide the cutting disc through the workpiece.
Do not exert pressure on the cutting disc. Allow the machine enough time to cut the
workpiece.
Cutting actions tends to slow the blade down. Pressure should therefore be occasionally
released to allow the blade to regain the full speed.
Regularly check if the cutting disc is sufficiently cooled.
Make sure that the cutting disc is cooled with water Add some cooling water if necessary.
Lock the head after use.
If holding the workpiece by hand take extreme care and ensure hand is kept
away from the cutting blade.
10.1 Switching on and off (fig. 6)
To switch the machine on, set the on/off switch (16) to ‘I’.
To switch the machine off, set the on/off switch (16) to ‘0’.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX242 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX242 in the language / languages: English as an attachment in your email.

The manual is 0,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX242

Powerplus POWX242 User Manual - German - 13 pages

Powerplus POWX242 User Manual - Dutch - 13 pages

Powerplus POWX242 User Manual - French - 13 pages

Powerplus POWX242 Additional guide - All languages - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info