582379
6
Zoom out
Zoom in
Previous page
1/12
Next page
POWX242 EN
Copyright © 2015 VARO p a g e | 6 www.varo.com
Do not perform any design, assembly or Construction activities on the table while the
machine is switched on.
Unplug the machine and clean the table before leaving the work area.
Wear protective glasses, dust mask, ear defenders, work gloves and protective-sliding
shoes.
Keep the table flat and do not scratch or press the table.
Do not put hands anywhere near the blade whilst it is rotating.
Do not attempt to free a jammed blade without first switching off or removing the plug from
the mains power supply.
Do not cut small workpiece and also do not use for a purpose not intended.
Keep water full in the tank when you operate the cutter.
Do not use any solvents for instead water in this tool.
6.1 Power supply
This tile saw must be connected to an earthed 230V - 50Hz power source.
This power source must be secured by a 16A fuse.
Your machine is supplied with a 30mA residual current device to protect the user against
electric shock.
It can only protect you when the power mains to which the tool is plugged is properly
grounded.
Have the proper outlet installed by a qualified electrician.
Check with a qualified electrician or service personnel if the grounding instructions are not
completely understood, or if in doubt as to whether the tool is properly grounded.
6.2 Using an extension lead
The use of any extension lead will cause some loss of power.
To keep this to a minimum and to prevent overheating and motor burn-out, ask advice
from a qualified electrician to determine the minimum wire size of the extension lead.
The extension lead should be equipped with an earthed type plug that fits the power
supply outlet at one end, and with an earthed type socket that fits the plug of the machine
at the other end.
7 ADDITIONAL SAFETY INSTRUCTIONS FOR LASERS
Warning! The laser beam potentially causes severe eye damage. Never look or stare
directly into the laser beam.
During use, do not point the laser beam at people, directly or indirectly through reflecting
surfaces.
This laser complies with class 2 according to EN 60825-1:2001. The unit includes no
servicing components. Do not open the housing for any reason. If the unit is damaged,
have the damage repaired by an authorized repair agent.
Attention
Laser beam
Do not stare into the beam
laser class 2
Laser class : class 2
Laser wave length : 650 nm
Laser output : ≤1 mW
The laser on this machine is equiped with 2 AAA batteries.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX242 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX242 in the language / languages: English as an attachment in your email.

The manual is 0,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX242

Powerplus POWX242 User Manual - German - 13 pages

Powerplus POWX242 User Manual - Dutch - 13 pages

Powerplus POWX242 User Manual - French - 13 pages

Powerplus POWX242 Additional guide - All languages - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info