Manual Powerplus POWX221 (page 8 of 13) (English)

675037

Zoom out

Zoom in

1/13

POWX221 EN

7.3 Assemble undercarriage Fig. G

 Turn the machine upside down.

 Remove the black plastic bottom plate by unscrewing the 6 screws. (Fig. G-1).

 Unscrew the adjusting knob on the front and tilt the motor (Fig. G-2), then remove the

transport packing (Fig. G-3).

 Now place one by one the uprights in the casing of the sawing bench (Fig. G-4).

 Secure the uprights with 4 screws using a screwdriver, do not completely tighten the

screws (Fig. G-5).

 Fit the 4 support bars, do not completely tighten the screws (Fig. G-6)

 Fit the black plastic bottom plate and screw it tight.

 Attach the rubber feet under the uprights (Fig. G-7).

 Turn the machine into an upright position on a flat surface and adjust the machine so that

it stands in a stable position, tighten all the nuts and bolts (Fig. G-7).

7.4 Assemble bracket/push stick.

 Attach the 2 brackets onto t he casing of the sawing bench and screw them tight (Fig. G-

8).

 Place the push stick in the brackets.

7.5 Assembly and attachment of the rip fence Fig. D

 Attach the aluminium fence (A) to the positioning block (B).

 Now you can attach the complete rip fence to the bench top.

 Slide the rip fence via one end of the positioning rail (C) over the bench top.

 Adjust the position of the aluminium fence profile (A) such that the end corresponds to the

rear edge of the saw.

7.6 Assembly of the riving knife and the protective cap Fig. E

 Turn the saw blade completely upwards.

 Remove the bench inlay.

 Assemble the riving knife on the set-up for this purpose and use hereby the Allen screws

and the filling rings. Ensure that the riving knife falls properly into the opening (= groove).

 Now put the inlay back in the bench and fasten it.

 Now assembly the protective cap onto the riving knife and use hereby the profiled nut and

self-locking nut.

Now lay a lath against the saw blade and the riving knife and check whether

it falls properly into the extension of the saw blade. If this is not the

case:Loosen the fastening bolts and place or remove the filling rings.

 Above the saw table the radial distance between the riving knife and the toothed rim of the

saw blade shall not at any point exceed 5 mm at the depth of cut set.

 The tip of the riving knife shall not be lower than 5 mm from the tooth peak, as shown.

7.7 Assembly of the saw blade

First remove the plug from the mains before the saw blade is assembled or

replaced.

 Remove the inlay from the bench. Use a screwdriver for this purpose.

 Turn the saw axle completely upwards. Remove the nut and the outside flange from the

saw axle.

 Now slide the saw blade over the saw axle and now put the outside flange and the nut

back. Tighten the nut by hand.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX221 in the language / languages: English as an attachment in your email.

The manual is 0,32 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX221

Powerplus POWX221 User Manual - German - 15 pages

Powerplus POWX221 User Manual - Dutch - 14 pages

Powerplus POWX221 User Manual - French - 14 pages

Powerplus POWX221 Additional guide - All languages - 4 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Powerplus POWX221 Manual

Product: