480927
17
Zoom out
Zoom in
Previous page
1/23
Next page
POWX0782 EN
Copyright © 2015 VARO P a g e | 17 www.varo.com
Check the power cable and plug for damages, and let damaged parts be replaced by a
certified electrician.
Check all moving parts, and make sure that they can move freely and smoothly over their
entire operational range.
Check the riving knife, and make sure that the distance between the riving knife and saw
blade is between 3 mm and 8 mm.
11.2.3 Monthly (if the saw is used every day)
Check the condition of the drive belt and the belt tension, and fix it if necessary.
11.2.4 Every 300 operating hours (Fig. 10)
- Check all screws and make sure that they are firmly attached; tighten up wherever
necessary.
-Check the lateral tolerance of the saw head, and adapt it if necessary by tightening the bolt
(P1).
- Check whether the saw head returns to its starting position when it is released; replace the
corresponding springs, if necessary.
- Check whether the movable saw blade guard functions.
TIPS:
For long workpieces, use suitable supports at both sides of the machine.
Use an additional mitre and width guide when sawing small pieces (this can be a small
board, which is attached to the guide with screws).
When sawing a warped workpiece, make sure that you position the convex side (namely
the outer side of the curve) of the workpiece against the guide.
Do not saw workpieces that are standing on edge. Always position workpieces flat on the
turntable.
Always keep support surfaces clean; it is above all important to remove resin residues with
a suitable cleaner or maintenance spray.
11.2.5 Changing the saw blade (Fig. 19-21)
HAZARD!
The saw blade may be extremely hot and can cause burns, immediately
after you have stopped sawing. Always led a hot saw blade cool off. Never
clean saw blades with flammable liquids.
This can cause injuries, also when the saw blade is not turning. The
movable saw blade guard must cover the saw blade, whenever you tighten
or release the driveshaft bolt (E1).
Always wear gloves while changing the saw blade.
Set the support arm to 0° (vertical) and tighten the bevelling lock nut.
For removing the topmost sawing table, loosen the corresponding screws. Remove the
sawing table.
To prevent that the saw blade rotates, pull the saw blade lock (D1) forward. Use your hand
at the same time to turn the saw blade slowly, until the saw blade latch is activated.
Loosen the driveshaft bolt (E1) of the saw (left-turning thread).
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0782 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0782 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0782

Powerplus POWX0782 User Manual - German - 24 pages

Powerplus POWX0782 User Manual - Dutch - 23 pages

Powerplus POWX0782 User Manual - French - 24 pages

Powerplus POWX0782 Additional guide - All languages - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info