480927
19
Zoom out
Zoom in
Previous page
1/23
Next page
POWX0782 EN
Copyright © 2015 VARO P a g e | 19 www.varo.com
The spanner must be removed, after the shaft that has been tightened.
Install the saw table and mount the corresponding screws.
11.2.6 Tightening the drive belt
The drive belt, which is located behind a plastic cover at the right-hand side of the saw head,
must be tensioned when there is more that 8 mm of play (when pushing on the middle
between the two wheels), or if drive power is no longer transmitted.
11.2.7 Checking the tension
Turn the saw head completely towards the top.
Set the support arm to 0° (vertical) and tighten the bevelling lock nut.
Loosen the bolt with which the saw blade guard is attached and then remove the saw
blade guard.
Release the topmost saw blade screw and remove the topmost sawing table.
Remove the cover (F1) next to the motor.
Use your fingers to check the tension of the drive belt through the opening. Tighten the
drive belt if there is more than 8 mm of play (see Paragraph 9.2.8 “Renewed tensioning” in
this regard).
11.2.8 Renewed tensioning (Fig. 23-26)
Loosen the two screws (J1) between the motor and the support arm.
For tensioning the drive belt, use the hexagonal screw (K1) to move the motor
backwards.
Tighten the screws (J1) crosswise while holding the motor in position.
Replace the topmost saw table and tighten the screws.
Reinstall the saw blade guard and tighten the screw that fixes the saw blade guard in
position.
Let the saw head come down completely.
- The moveable saw blade guard must open without touching the saw blade.
- When the saw head returns to the starting position, then the movable saw blade guard
must automatically enclose the saw blade.
- In the topmost starting position of the saw blade, the safety lock of the movable saw guard
must be engaged, so as to prevent an undesirable opening.
- Check the saw blade lock; the saw blade must be able to rotate freely.
11.2.9 Replacing the saw guide (21)
HAZARD!
If the saw guide has been damaged, then small pieces can become jammed between the
guide and the saw, which can block the saw blade. Immediately replace a defective saw
guide. (Fig. 7).
Remove the saw guide (13).
Remove the defective piece by dislodging it with a screwdriver.
Insert a new piece and click it in position.
Reinstall the saw guide (13).
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0782 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0782 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0782

Powerplus POWX0782 User Manual - German - 24 pages

Powerplus POWX0782 User Manual - Dutch - 23 pages

Powerplus POWX0782 User Manual - French - 24 pages

Powerplus POWX0782 Additional guide - All languages - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info