795413
9
Zoom out
Zoom in
Previous page
1/14
Next page
POWX07588 EN
Copyright © 2022 VARO P a g e | 9 www.varo.com
9 OPERATION
Risk of injury! In the event of a functional fault, immediately press the red
button 0 on the On / Off switch and unplug.
9.1 Check before starting the device!
Risk of injury! The device may only be put into operation if there are no
defects. If a part is defective danger it must be replaced before the device is
used again.
Check to make sure the device is in safe operating condition:
Check to make sure there are no visible defects.
Check to make sure all device components are correctly mounted.
Check to make sure the safety equipment is functioning properly.
Check to make sure that the saw blade runs freely.
Check whether the adjusting screw for setting the angle of tilt is tightened.
9.2 On/off switch
Switching on: Pressing the green button I on the On / Off switch (1) switches on the saw.
Before starting to saw, wait until the blade has reached maximum speed.
Switching off: Pressing the red button 0 on the On / Off switch (1) switches off the saw.
9.3 Workpiece stops
9.3.1 Mitre angle stop (Fig. 10)
For cross-cutting of wooden parts, the Mitre guide(10) must be used.
Fix the Mitre guide extension (19) to the Mitre guide (10) with the knobs for mitre guide.
Push the Mitre guide(10) into the groove of the table surface.
Loosen the knob for mitre angle (12).
Turn the Mitre guide extension (19) until the arrow points to the desired angle.
Tighten the knob for mitre angle (12) again.
Check the distance between Mitre guide extension (19) and saw blade (15).
Warning! Do not push the Mitre guide extension (19) too far towards the
saw blade. The distance between Mitre guide extension (19) and saw blade
(15) should be approx. 2 cm. If necessary, loosen the two knobs for mitre
guide and adjust the Mitre guide extension (19). Afterwards, retighten the
knobs for mitre guide.
9.3.2 Parallel stop (Fig. 8-9)
Do not use the paralell stop and miter gauge at the same time!
When slitting wood parts, the Parallel guide (11) must be used.
Mount the Parallel guide (11) on the table surface (14) with the clamping plate (26);
Washers (27) and knobs (12): Outside of the saw table: set screw (12) and washer (27);
Inside of the saw table: clamping plate (26).
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX07588 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX07588 in the language / languages: English as an attachment in your email.

The manual is 0.27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX07588

Powerplus POWX07588 User Manual - German - 15 pages

Powerplus POWX07588 User Manual - Dutch - 14 pages

Powerplus POWX07588 User Manual - French - 14 pages

Powerplus POWX07588 Additional guide - All languages - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info