Manual Powerplus POWX07562 (page 7 of 11) (English)

675015

Zoom out

Zoom in

1/11

POWX07562 EN

Caution! A return spring causes the machine head to rise automatically at the end of the cut.

Do not let go of the handle (3) as soon as the cut is completed but steady the machine head

and allow it to rise slowly.

8.4 Precision adjustment of the stop for 90° cross-cuts (Fig. 4)

 Lower the machine head (4) and fix with the lock pin (20).

 Place the stop angle between the saw blade (5) and the rotary table (8).

 Slacken the counter nut (22) and adjust the setting screw (23) until the angle between the

saw blade (5) and the rotary table (8) equals 90°.

 Re-tighten the counter nut (22) to fix the machine in this setting.

8.5 90° cross-cuts and 0°-45° rotary table (Fig. 5)

 The POWX07562 can be used to make angled cuts of 0°-45° relative to the stop rail on

the left and right side.

 You can adjust the angle by moving the table to the left or to the right using the handle.

(24)

 Release the rotary table (8) by slackening the locking handle (24) and pressing the latch

(30).

 Turn the rotary table (8) by its handle (24) to the angle you want, i.e. the mark (a) on the

rotary table has to comply with the required angle dimension (21) on the base plate (9).

 Re-tighten handle (24)

8.6 Mitre cuts 0°-45° and rotary table 0° (Fig. 6)

 The POWX07562 can be used to make mitre cuts of 0°-45° relative to the machine bed on

the left side.

 Lift the machine head (4) to its top position.

 Fix the rotary table (8) in 0° position.

 Undo the tightening screw (10) and use the handle (3) to tilt the machine head (4) to the

left until the pointer (a) coincides with the required angle value (19).

 Re-tighten the tightening screw (10)

8.7 Precision adjustment of the stop for 45° mitre cuts (Fig. 7)

 Lower the machine head (4) and fix with the lock pin (20).

 Fix the rotary table (8) in 0° position.

 Undo the tightening screw (10) and use the handle (3) to tilt the machine head (4) to the

left until it coincides at 45°.

 Place a 45° stop angle between the saw blade (5) and the rotary table (8).

 Slacken the counter nut (25) and adjust the setting screw (26) until the angle between the

saw (5) and the rotary table (8) equals exactly 45°.

8.8 Mitre cuts 0-45° and rotary table 0-45°

 The POWX07562 can be used to make mitre cuts on the left at an angle of 0°-45° relative

to the work top and 0°-45° relative to the stop rail.

 Lift the machine head (4) to its top position.

 Adjust the rotary table (8) by its handle (24) to the required angle.

 Undo the tightening screw (10) and use the handle (3) to tilt the machine head (4) to the

left until it coincides with the required angle value.

 Screw the tightening screw (10) back down again.

9 DUST BAG

The saw is equipped with a bag (18) to collect sawdust and chips. You can pull off the

sawdust bag (18) to the rear by pressing together the two clips. To empty the bag, undo the

zip at the bottom.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX07562 in the language / languages: English as an attachment in your email.

The manual is 0,3 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX07562

Powerplus POWX07562 User Manual - German - 11 pages

Powerplus POWX07562 User Manual - Dutch - 11 pages

Powerplus POWX07562 User Manual - French - 11 pages

Powerplus POWX07562 Additional guide - All languages - 6 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Powerplus POWX07562 Manual

Product: