675015
6
Zoom out
Zoom in
Previous page
1/11
Next page
POWX07562 EN
Copyright © 2017 VARO P a g e | 6 www.varo.com
5.5 Service
Your power tool should be serviced by a qualified specialist using only standard spare
parts. This will ensure that it meets the required safety standards.
6 ADDITIONAL SAFETY INSTRUCTIONS FOR LASERS
Warning! The laser beam potentially causes severe eye damage. Never look or stare
directly into the laser beam.
During use, do not point the laser beam at people, directly or indirectly through reflecting
surfaces.
This laser complies with class 2 according to EN 60825-1:2001. The unit includes no
servicing components. Do not open the housing for any reason. If the unit is damaged,
have the damage repaired by an authorized repair agent.
7 ADDITIONAL SAFETY INSTRUCTIONS FOR BATTERIES
When replacing batteries, always replace the complete set. Do not mix old batteries with
new ones.
Prevent removed batteries from short circuiting.
Do not store batteries where the temperature may rise above 50 °C, e.g. in a car which
has been parked in the sun.
Do not burn batteries.
Never attempt to open batteries.
In case of battery leakage, carefully remove the liquid using a cloth. Avoid skin or eye
contact. Do not swallow. In case of skin or eye contact, rinse abundantly for 10 minutes
with clean water and consult a physician.
8 ASSEMBLY
8.1 Setting up the saw (Fig.1)
Insert the two workpiece support clips (11) in the mounts (12) provided on the side of the
tool and fasten them in place with the screws (13).
Insert the clamping device (14) into one of the two mounts (15) provided on the top of stop
rail and fasten in place with the thumb screw (16).
Screw the additional stability bar (17) to the back of the machine.
8.2 Adjusting the saw (Fig. 2)
The rotary table (8) has latching positions at 0°, 15°, 22.5°, 30° and 45°. You can adjust
the angle by moving the table to the left or to the right using the handle (24).
While pressing down lightly the machine head (4), pull the lock pin (20) out of the motor
holder to disengage the saw from its bottom working position.
Swing up the machine head until the retaining hook latches home.
By loosening the lock screw (10), the machine head (4) can be angled to the left up to 45°.
Check that the voltage marked on the rating plate is the same as your mains voltage and
connect up the machine.
8.3 90° cross-cuts and 0° rotary table (Fig. 3)
To turn the machine on press the on/off switch (1)
Important! Place the material you want to saw flat on the machine surface and secure with
the clamping device (14) so that the material cannot move while you are cutting.
After switching on the saw, wait for the blade (5) to reach its maximum speed.
Press the release lever (1) sideways and, using the handle (3), apply steady and light
downward pressure to move the machine head through the workpiece.
When the cut is completed, return the machine to its top parking position and let go of the
On/Off switch.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX07562 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX07562 in the language / languages: English as an attachment in your email.

The manual is 0,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX07562

Powerplus POWX07562 User Manual - German - 11 pages

Powerplus POWX07562 User Manual - Dutch - 11 pages

Powerplus POWX07562 User Manual - French - 11 pages

Powerplus POWX07562 Additional guide - All languages - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info