582664
8
Zoom out
Zoom in
Previous page
1/14
Next page
POWX0561 EN
Copyright © 2014 VARO P a g e | 8 www.varo.com
9 PREPARATION
Before each use check the proper function of all installation fixtures of the plunge saw and
only use the plunge saw if everything works properly.
Attach the work piece in such way that it cannot move or bend during work. Line the work
piece respectively.
Always hold the plunge saw with both hands at the hand grips (3) and (4).
Always guide the plunge saw forward. Never draw the plunge saw back!
Place the plunge saw with the front part of the base plate (5) on the work piece. Guide the
plunge saw only against the work piece during operation.
With the correct forward speed you prevent overheating of the saw blade, and melting
when cutting plastics.
10 OPERATION
10.1 Switching ON/OFF
Press the switch lock (2) and then the ON/OFF switch (1) to switch the plunge saw on.
Release the ON/OFF switch (1) to switch the plunge saw off.
Notes: Pressing the switch lock (2) unlocks the plunge cut mechanism at the same time, so
that the blade can be moved downwards. The saw blade emerges from the protective cover.
When lifting the saw the motor slides back into the initial position.
10.2 Setting the cutting depth
The cutting depth can be set between 0 - 54 mm:
Loosen the cutting depth limit stop knob (9) and slide it to the desired cutting depth
according to the graduated scale (11) to set the cutting depth.
Note: The graduated values on the scale (11) apply for straight cuts (90° cut).
The guide rail depth adjustment stopper (10) must be tilted up when using the plunge saw
without guide rail. Only when using the plunge saw with guide rail, the guide rail depth
adjustment stopper is used to compensate for the thickness of the guide rail.
(Fig 2)
Using the guide rail = guide rail depth adjustment stopper down.
Not using the guide rail = guide rail depth adjustment stopper up.
(Fig. 3)Tighten the cutting depth limit stop knob (9). The motor or respectively the saw
blade can now be pushed down to the set cutting depth.
For a clean, safe cut set the cutting depth in such way that only max. one saw blade tooth
protrudes under the work piece.
10.3 Setting the cutting angle (Fig. 4)
The plunge saw can be swiveled between 0° and 48°:
Loosen both rotary knobs (8). Swivel the motor to the desired cutting angle on the cutting
angle scale.
Tighten the rotary knobs (8) again
Always hold the plunge saw with both hands.
Always guide the plunge saw forward. Never draw the plung saw back!
10.4 Determine Cutting line (Fig. 5)
Two cutting lines are marked on the base plate (5) of the plunge saw.
Align position A (0 mark on base plate) at the front of the base plate with your marked
cutting line when using the plunge saw without guide rail for straight cuts.
For 45° miter cuts align position B (45 mark on base plate) at the front of the base plate
with your marked cutting line.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0561 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0561 in the language / languages: English as an attachment in your email.

The manual is 0,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0561

Powerplus POWX0561 User Manual - German - 15 pages

Powerplus POWX0561 User Manual - Dutch - 15 pages

Powerplus POWX0561 User Manual - French - 15 pages

Powerplus POWX0561 Additional guide - All languages - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info