582664
10
Zoom out
Zoom in
Previous page
1/14
Next page
POWX0561 EN
Copyright © 2014 VARO P a g e | 10 www.varo.com
The cutting width marks (15) show the most foremost and rearmost cutting points of the
saw blade (Ø 165 mm) at maximum cutting depth and when using the guide rail.
10.9 Replacing the saw blade
Before any maintenance work always switch off the plunge saw and
disconnect from mains power.
Loosen both rotary knobs (8) and swivel the plunge saw to 0° position before changing the
saw blade. Tighten the rotary knobs again.
Set the selector switch (17) to the change saw blade icon.
Press the switch lock (2) down and push the motor down.
Press and hold the spindle arrester down.
Use a 5 mm Allen key to turn the screw at the saw blade slightly clockwise or counter-
clockwise until the spindle clicks into place.
Use the Allen key to loosen the screw counter-clockwise. Remove the outer flange and the
saw blade.
Clean both flanges and replace the saw blade.
Note: The rotation direction arrows of saw blade and saw must be aligned!
Replace the outer flange in such way that the slaving pins sit in the recesses of the inner
flange.
Press and hold the shaft lock b utton and tighten the screw. Press the switch lock (2) for
the casing to swivel up again.
11 FINE ADJUSTMENT OF PLUNGE SAW PLAY ON GUIDE RAIL
The play of the base plate on the guide rail can be reduced to minimum with the fine
adjustment screws (7).
Loosen the fine adjustment screws counter-clockwise.
Turn both fine adjustment screws (7) clockwise to minimize the play between base plate
and guide rail, if necessary.
Fasten the fine adjustment screws clockwise.
12 CONNECTING RODS FOR GUIDE RAILS (FIG. 7)
To connect both guide rails slide the first connecting rod from the bottom into the groove of
the guide rail.
Slide the other connecting rod into the second groove.
Use the 3 mm Allen key to tighten the stud screws to the limit stop to connect the rails.
13 GUIDE RAIL SPLINTER GUARDS (FIG. 8)
The guide rails come with a splinter guard (black protruding rubber lip). The splinter guard
should be cut to size before first use. The splinter guard ensures a tear-free cut, since the
wood fibers at the top of the work piece are torn without splinter guard. This is due to the saw
blade teeth being directed upward.
After cutting the splinter guard to size it also shows the precise cutting path of the saw blade.
Mark a cutting line on the work piece and align the guide rail exactly with this cutting line.
Fix the guide rail with clamps on the work piece.
Set the selector switch to marked cut function. Set the plunge saw speed to 6.
Place the plunge saw at the rear end of the guide rail.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0561 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0561 in the language / languages: English as an attachment in your email.

The manual is 0,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0561

Powerplus POWX0561 User Manual - German - 15 pages

Powerplus POWX0561 User Manual - Dutch - 15 pages

Powerplus POWX0561 User Manual - French - 15 pages

Powerplus POWX0561 Additional guide - All languages - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info