481010
8
Zoom out
Zoom in
Previous page
1/11
Next page
POW8135 EN
Copyright © 2007 VARO Vic. Van Rompuy N.V. www.varo.com Page | 8
9.7 Precision adjustment of the stop for 45° mitre cuts (Fig. 8/9)
§ Lower the machine head (4) and fix with the lock pin (16).
§ Fix the rotary table (8) in 0° position.
§ Undo the tightening screw (12) and use the handle (2) to tilt the machine head (4) to the left
until it coincides at 45°.
§ Place the 45° stop angle (A) between the saw blade (5) and the rotary table (8).
§ Slacken the counter nut (25) and adjust the setting screw (26) until the angle between the
saw (5) and the rotary table (8) equals exactly 45°.
9.8 Mitre cuts 0-45 and rotary table 0-45" (Fig. 10)
§ The POW8130 can be used to make mitre cuts on the left at an angle of 0°-45° relative to
the work top and-45° relative to the stop rail.
§ Lift the machine head (4) to its top position.
§ Undo the rotary table (8) by slackening the locking handle (10) and pressing the latch (11).
§ Adjust the rotary table (8) by its handle (2) to the required angle (see also Section D).
§ Retighten the tightening screw (10) in order to secure the turntable in place.
§ Undo the tightening screw (12) and use the handle (2) to tilt the machine head (4) to the left
until it coincides with the required angle value (in this connection see also section E).
§ Screw the tightening screw (12) back down again.
10 DUST BAG (FIG. 2)
The saw is equipped with a bag (14) to collect sawdust and chips. You can pull off the
sawdust bag (14) to the rear by pressing together the two clips (27). To empty the bag, undo
the zip at the bottom.
11 REPLACING THE SAW BLADE (FIG. 5/11)
§ Pull out the power plug.
§ Swing up the machine head (4).
§ Unscrew the two bolts (27, 28) and flip the cover plate up together with the saw blade guard
(6).
§ Press the saw shaft lock (17) with one hand while holding the wrench (32) on the flange bolt
(25) with the other.
§ Firmly press on the saw shaft lock (17) and slowly rotate the flange bolt (25) in clockwise
direction. The saw shaft lock engages after no more than one rotation.
§ Now, using a little more force, slacken the flange bolt (25) in clockwise direction.
§ Turn the flange bolt (25) until it is completely removed.
§ Take the blade (5) off the inner flange and pull out downwards.
§ Mount the new saw blade in reverse order and fasten.
§ Important! The cutting bevel of the teeth, i.e. the
§ direction of rotation of the saw blade, has to conform with the direction of the arrow marked
on the housing.
§ Clean the saw blade flanges thoroughly before mounting the saw blade.
§ Reattach the movable blade guard (6) in reverse order.
§ Before using the saw again, check that the safety devices are in good working order.
§ Important: Every time that you change the saw blade, check to see that it spins freely in the
groove of the turntable in both perpendicular and 45° angle settings.
12 ASSISTANT FENCE FUNCTION (FIG 14)
§ When angle of blade is 9, please fit on part (A)
§ When angle of blade is 4, please loose screw (a) to remove part (A)
13 LASER FUNCTION (FIG. 12)
You can switch the laser ON and OFF with the switch (a).
The laser (35) directs a beam onto the work-piece.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POW8135 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POW8135 in the language / languages: English as an attachment in your email.

The manual is 0,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POW8135

Powerplus POW8135 User Manual - German - 11 pages

Powerplus POW8135 User Manual - Dutch - 11 pages

Powerplus POW8135 User Manual - French - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info