481010

Powerplus POW8135 Manual

7
Zoom out
Zoom in
Previous page
1/11
Next page
POW8135 EN
Copyright © 2007 VARO – Vic. Van Rompuy N.V. – www.varo.com Page | 7
9.2 Adjusting the saw (Fig. 1/2)
§ To adjust the rotary table (8), slacken the locking handle (10) by approx. 2 turns and press
the latch (11) in order to unlock the rotary table (8).
§ The rotary table (8) has latching positions at 0°, 15°, 22.5°, 30° and 45°. Once the latch (11)
is engaged you must also tighten the locking handle (10) in order to fix the table in position.
§ If you need to work with any other angles, the rotary table is fixed in position with just the
locking handle (10).
§ While pressing down lightly on the machine head (4), pull the lock pin (16) out of the motor
holder to disengage the saw from its bottom working position.
§ Swing up the machine head until the retaining hook latches home.
§ By loosening the lock screw (12), the machine head (4) can be angled to the left up to 45°.
§ Check that the voltage marked on the rating plate is the same as your mains voltage and
connect up the machine.
9.3 90° cross-cuts and 0° rotary table (Fig. 1)
§ To turn the machine on, simultaneously press the main switch (3) and locking button (30).
§ Important! Place the material you want to saw flat on the machine surface and secure with
the clamping device (19) so that the material cannot move while you are cutting.
§ After switching on the saw, wait for the blade (5) to reach its maximum speed.
§ Press the release lever (1) sideways and, using the handle (2), apply steady and light
downward pressure to move the machine head through the workpiece.
§ When the cut is completed, return the machine to
§ its top parking position and let go of the On/Off
§ switch.
Caution! A return spring causes the machine head to rise automatically at the end of the cut.
Do not let go of the handle (2) as soon as the cut is completed but steady the machine head
and allow it to rise slowly.
9.4 Precision adjustment of the stop for 90° cross-cuts (Fig. 4/5)
§ Lower the machine head (4) and fix with the lock pin (16).
§ Slacken the tightening screw (12).
§ Place the stop angle (A) between the saw blade (5) and the rotary table (8).
§ Slacken the counter nut (23) and adjust the setting screw (24) until the angle between the
saw blade (5) and the rotary table (8) equals 90°.
§ Re-tighten the counter nut (23) to fix the machine in this setting.
9.5 90° cross-cuts and 0°-45° rotary table (Fig.6)
§ The POW8130 can be used to make angled cuts of 0°-45° relative to the stop rail on the left
and right side.
§ Release the rotary table (8) by slackening the locking handle (10) and pressing the latch
(11).
§ Turn the rotary table (8) by its handle (2) to the angle you want, i.e. the mark (a) on the
rotary table has to comply with the required angle dimension (17) on the base plate (9).
§ Re-tighten the locking handle (10) in order to fix the rotary table (8) in position.
§ Make the cut as described in Section B.).
9.6 Mitre cuts 0°-45° and rotary table 0° (Fig. 4/7)
§ The POW8130 can be used to make mitre cuts of 0°-45° relative to the machine bed on the
left side.
§ Lift the machine head (4) to its top position.
§ Fix the rotary table (8) in 0° position.
§ Undo the tightening screw (12) and use the handle (2) to tilt the machine head (4) to the left
until the pointer (a) coincides with the required angle value (15).
§ Re-tighten the locking nut (12) and make the cut as described in Section B.).
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POW8135 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POW8135 in the language / languages: English as an attachment in your email.

The manual is 0,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POW8135

Powerplus POW8135 User Manual - German - 11 pages

Powerplus POW8135 User Manual - Dutch - 11 pages

Powerplus POW8135 User Manual - French - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info