426967
6
Zoom out
Zoom in
Previous page
1/11
Next page
POWX093 EN
Copyright © 2017 VARO P a g e | 6 www.varo.com
Ensure that milling cutter is firmly clamped.
Use only milling cutters for routers; never use e.g. milling cutters for drilling machines or
stationary machines.
Use only commercially available milling cutters for routers with a shank diameter 6 mm or
8 mm.
Always use both hands to guide the tool.
Never wedge the ON switch fast.
Never reach into the milling zone while the tool is running.
Feed only running milling cutters to the material.
Note direction of cut - always move the cutter against the material.
When work is finished, remove the milling cutter from the tool.
Wood dust set up during work is harmful to health. Always work with dust collector
operating.
Wear protective goggles, ear protectors and, if necessary, breathing mask.
Observe general safety regulations for handling and using electric tools..
7 OPERATION
7.1 Depth Stop (Fig. 1 & 2)
Locate the depth stop on the left-hand side of the cutting machine. This continuously
adjustable stop is intended to limit the depth of the cut. Locate the fixing screw for the depth
stop (1). Loosen it by turning it in anticlockwise direction. To move the depth stop up or down,
turn the stop adjuster in clockwise or anticlockwise direction (2).
7.2 Locking lever for cutting machine body (Fig. 3 & 4)
When viewed from the front, the locking lever (3) is located at the rear on the left-hand side.
The cutting machine body is spring-tensioned. Take care when releasing the locking lever.
Grasp both handles and brace yourself before releasing the lever (4). Press downwards to
allow the cutting machine body to move down. When you reduce the downward pressure, the
springs force the cutting machine body back up into its highest position.
CAUTION: The housing of the machine is under spring tension. When you release the locking
lever, it returns to its highest position..
7.3 Dust extraction outlet (Fig. 5, 6 & 7)
You are advised to use the dust extraction outlet. You can purchase
a suitable commercial vacuum cleaner or extract the dust via an
extractor tube while the cutting machine is in operation. The outlet
must project out of the rear of the machine (5). Two bolts and nuts
are supplied to attach it.
Hold the extractor outlet in position and lay the cutting machine on its side. Push the long bolt
through the machine base until it projects at the fastening point for the extractor outlet (6).
Place the nut in the hexagon-shaped recess (7). Tighten the bolt with a suitable wrench and
moderate force until the outlet is securely attached. Repeat the procedure at the other side
CAUTION: Dust may cause respiratory problems. Certain laminated board
materials are carcinogenic. After work, always remove all dust from the
machine.
7.4 Assembly of parallel stop Fig. 8 & 9)
Locate the parallel stop and the guide rods. Push the guide rods into the casting and secure
them with the adjusting screws (8). Inspect the machine base and the four securing points.
Loosen the locking screws and push the guide rods into the machine base (9). The parallel
stop is continuously adjustable and permits various parallel cuts.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus pow x093 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus pow x093 in the language / languages: English as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus pow x093

Powerplus pow x093 User Manual - German - 12 pages

Powerplus pow x093 User Manual - Dutch - 11 pages

Powerplus pow x093 User Manual - Dutch - 13 pages

Powerplus pow x093 User Manual - Dutch - 13 pages

Powerplus pow x093 User Manual - French - 12 pages

Powerplus pow x093 Additional guide - All languages - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info