628495

Polycom Vortex EF2280 Manual

42
Zoom out
Zoom in
Previous page
1/105
Next page
This command sets the hold time (in milliseconds) for the camera gating (CGATE) feature.
This command is an integer command. See
Section 6.2 for more information on this type of command. The
minimum and maximum values for this command are 100 and 5000, respectively.
This command is saved to non-volatile memory only as part of a preset. The state of this command will be
restored after power-up only if a preset is saved and that preset is set to be the power-on preset.
Example Description Status Message
F01CGATET500
Set camera gating hold time to 500
ms.
F01CGATET500
F01CGATET>500
Increase camera gating hold time by
500 ms.
F01CGATETx , where x is between 100 and 5000
depending on the current setting of CGATET. If this
command is issued after the example above, the
status message will be F01CGATET1000 .
F01CGATET?
Query camera gating hold.
F01CGATETx , where x is between 100 and 5000
depending on the current setting of CGATET. If this
command is issued after the example above, the
status message will be F01CGATET1000 .
8.37. DELAYO -- Set Output Delay
This command sets the amount of output delay (in tenths of milliseconds) on each of the twelve output channels
(1-8, A-D) . Use of the wildcard character (*) for specifying the channel is not supported for this command. The
output delay can be separately enabled or disabled via the
DELAYOE command.
The output delay feature is only available on Rev F and later EF2280's. All Rev F and later EF2280's have the
Polycom logo on the front panel. EF2280 revisions earlier than Rev F have the ASPI Digital logo on the front
panel. For units where this command is not supported, it will always return a status message indicating that the
output delay is set to 0.
This command is an integer command. See
Section 6.2 for more information on this type of command. The
minimum and maximum values for this command are 0 and 3400, respectively.
This command is saved to non-volatile memory only as part of a preset. The state of this command will be
restored after power-up only if a preset is saved and that preset is set to be the power-on preset.
Example Description Status Message
F01DELAYO21500
Set output delay on output channel 2
to 150 ms (1500 tenths of
milliseconds).
F01DELAYO21500
F01DELAYO2>1700
Increase output delay on output
channel 2 by 170 ms (1700 tenths of
milliseconds.)
F01DELAYO2x , where x is between 0 and 3400
depending on the current output delay setting for
output channel 2 . If this command is issued after
the above example, then the status message will be
F01DELAYO23200 .
… 42 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Polycom Vortex EF2280 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Polycom Vortex EF2280 in the language / languages: English as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Polycom Vortex EF2280

Polycom Vortex EF2280 User Manual - English - 62 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info