628495
40
Zoom out
Zoom in
Previous page
1/105
Next page
to send out 'ATDT4048921180' via its RS-232 port. If a modem was connected to the RS-232 port, this
command would cause the modem to dial the Polycom Installed Voice Business Group in Atlanta.
Example Description Status Message
F01BROAD2:ATDT4048921180
Sends the string ATDT4048921180 out the RS-232 port.
F01BROAD2
8.32. BROADA -- Broadcast Commands to Other Connected
Devices
This command is used to broadcast commands to other connected Polycom devices via the EF Bus and/or ASPI
Bus. For example, the command 'F01BROADA:B02PHONE1 ' would cause device ID 1 to send a command to the
EF2241 at device ID 2 to tell it to take its phone off-hook. The EF2241 at device ID 2 would respond by taking its
device off-hook and sending an acknowledgement.
This command is usually used in macros when one needs to have a macro on one device trigger an action on
another device.
Example Description Status Message
F01BROADA:B02PHONE1
Sends the command B02PHONE2 over
the digital bus.
F01BROADA
B02PHONE1, this second status message
is from the EF2241 at device ID 2 when it
takes its phone off hook.
8.33. BUSREF -- Set Which AEC Reference is Placed on EF Bus
This command sets or queries whic AEC reference (if any) is placed on the EF Bus. Setting BUSREF to '0' means
that no reference is placed on the EF Bus. Setting BUSREF to '1' means that AEC reference 1 (R1) is placed on
the bus. Setting BUSREF to '2' means that AEC reference 2 (R2) is placed on the bus.
The AEC references are created in the main matrix via outputs R1 and R2.
Only one Vortex can put a reference on the EF Bus at a time. If more than one Vortex places its reference on the
EF Bus, then an 'ERROR#093' will occur.
This command is an integer command. See
Section 6.2 for more information on this type of command. The
minimum and maximum values for this command are 0 and 2, respectively.
This command is saved to non-volatile memory only as part of a preset. The state of this command will be
restored after power-up only if a preset is saved and that preset is set to be the power-on preset.
Example Description Status Message
F01BUSREF2
Put AEC Reference 2 (R2) on the EF Bus.
F01BUSREF2
F01BUSREF0
Set Vortex to not place any AEC reference on
the EF Bus.
F01BUSREF0
F01BUSREF?
Query which AEC reference this Vortex is
placing on the EF Bus.
F01BUSREFx , where x is 0, 1, or 2 depending
on which AEC reference (if any) is currently
being placed on EF Bus.
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Polycom Vortex EF2280 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Polycom Vortex EF2280 in the language / languages: English as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Polycom Vortex EF2280

Polycom Vortex EF2280 User Manual - English - 62 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info