Manual Pioneer VSX-531D (page 27 of 41) (Finnish)

699667

Zoom out

Zoom in

1/41

Connecting your equipment

Placing the speakers

By connecting the left and right front speakers (L/R), the center speaker (C), the left and right

surround speakers (SL/SR), and the subwoofer (SW), a 5.1 ch surround system can be

enjoyed.

To achieve the best possible surround sound, install your speakers as shown below.

Hints on the speaker placement

Where you put your speakers in the room has a big effect on the quality of the sound. The

following guidelines should help you to get the best sound from your system.

•

The subwoofer can be placed on the floor. Ideally, the other speakers should be at about

ear-level when you’re listening to them. Putting the speakers on the floor (except the

subwoofer), or mounting them very high on a wall is not recommended.

•

For the best stereo effect, place the front speakers 2 m to 3 m apart, at equal distance from

the TV.

•

If you’re going to place speakers around your CRT TV, use shielded speakers or place the

speakers at a sufficient distance from your CRT TV.

•

If you’re using a center speaker, place the front speakers at a wider angle. If not, place

them at a narrower angle.

•

Place the center speaker above or below the TV so that the sound of the center channel is

localized at the TV screen. Also, make sure the center speaker does not cross the line

formed by the leading edge of the front left and right speakers.

•

It is best to angle the speakers towards the listening position. The angle depends on the

size of the room. Use less of an angle for bigger rooms.

•

The optimal positioning for surround speakers is just above ear height. Make sure the

speakers don’t face each other. For DVD-Audio, the speakers should be more directly

behind the listener than for home theater playback.

•

Try not to place the surround speakers farther away from the listening position than the

front and center speakers. Doing so can weaken the surround sound effect.

CAUTION

•

Make sure that all speakers are securely installed. This not only improves sound quality,

but also reduces the risk of damage or injury resulting from speakers being knocked over

or falling in the event of external shocks such as earthquakes.

120

5.1 channel surround system:

Connecting your equipment

Placing the speakers

By connecting the left and right front speakers (L/R), the center speaker (C), the left and right

surround speakers (SL/SR), and the subwoofer (SW), a 5.1 ch surround system can be

enjoyed.

To achieve the best possible surround sound, install your speakers as shown below.

Hints on the speaker placement

Where you put your speakers in the room has a big effect on the quality of the sound. The

following guidelines should help you to get the best sound from your system.

•

The subwoofer can be placed on the floor. Ideally, the other speakers should be at about

ear-level when you’re listening to them. Putting the speakers on the floor (except the

subwoofer), or mounting them very high on a wall is not recommended.

•

For the best stereo effect, place the front speakers 2 m to 3 m apart, at equal distance from

the TV.

•

If you’re going to place speakers around your CRT TV, use shielded speakers or place the

speakers at a sufficient distance from your CRT TV.

•

If you’re using a center speaker, place the front speakers at a wider angle. If not, place

them at a narrower angle.

•

Place the center speaker above or below the TV so that the sound of the center channel is

localized at the TV screen. Also, make sure the center speaker does not cross the line

formed by the leading edge of the front left and right speakers.

•

It is best to angle the speakers towards the listening position. The angle depends on the

size of the room. Use less of an angle for bigger rooms.

•

The optimal positioning for surround speakers is just above ear height. Make sure the

speakers don’t face each other. For DVD-Audio, the speakers should be more directly

behind the listener than for home theater playback.

•

Try not to place the surround speakers farther away from the listening position than the

front and center speakers. Doing so can weaken the surround sound effect.

CAUTION

•

Make sure that all speakers are securely installed. This not only improves sound quality,

but also reduces the risk of damage or injury resulting from speakers being knocked over

or falling in the event of external shocks such as earthquakes.

120

5.1 channel surround system:

Connecting your equipment

Placing the speakers

By connecting the left and right front speakers (L/R), the center speaker (C), the left and right

surround speakers (SL/SR), and the subwoofer (SW), a 5.1 ch surround system can be

enjoyed.

To achieve the best possible surround sound, install your speakers as shown below.

Hints on the speaker placement

Where you put your speakers in the room has a big effect on the quality of the sound. The

following guidelines should help you to get the best sound from your system.

•

The subwoofer can be placed on the floor. Ideally, the other speakers should be at about

ear-level when you’re listening to them. Putting the speakers on the floor (except the

subwoofer), or mounting them very high on a wall is not recommended.

•

For the best stereo effect, place the front speakers 2 m to 3 m apart, at equal distance from

the TV.

•

If you’re going to place speakers around your CRT TV, use shielded speakers or place the

speakers at a sufficient distance from your CRT TV.

•

If you’re using a center speaker, place the front speakers at a wider angle. If not, place

them at a narrower angle.

•

Place the center speaker above or below the TV so that the sound of the center channel is

localized at the TV screen. Also, make sure the center speaker does not cross the line

formed by the leading edge of the front left and right speakers.

•

It is best to angle the speakers towards the listening position. The angle depends on the

size of the room. Use less of an angle for bigger rooms.

•

The optimal positioning for surround speakers is just above ear height. Make sure the

speakers don’t face each other. For DVD-Audio, the speakers should be more directly

behind the listener than for home theater playback.

•

Try not to place the surround speakers farther away from the listening position than the

front and center speakers. Doing so can weaken the surround sound effect.

CAUTION

•

Make sure that all speakers are securely installed. This not only improves sound quality,

but also reduces the risk of damage or injury resulting from speakers being knocked over

or falling in the event of external shocks such as earthquakes.

120

5.1 channel surround system:

Kuuntelu laitteistolla

Listening to your system

Using the Advanced Sound Retriever

When audio data is removed during the compression

process, sound quality often suffers from an uneven sound

image. The Advanced Sound Retriever feature employs new

DSP technology that helps bring CD quality sound back to

compressed 2-channel audio by restoring sound pressure

and smoothing jagged artifacts left over after compression.

…

Press

S.RETRIEVER

to switch the S.RTV (Advanced

Sound Retriever) ON or OFF.

Note

• The Advanced Sound Retriever mode cannot be set to

when the

DIRECT

mode or the

PURE DIRECT

mode is

switched on.

Better sound using Phase Control

This receiver’s Phase Control feature uses phase correction

measures to make sure your sound source arrives at the

listening position in phase, preventing unwanted distortion

and/or coloring of the sound.

Phase Control technology provides coherent sound

reproduction through the use of phase matching for an

optimal sound image at your listening position. The default

setting is on and we recommend leaving Phase Control

switched on for all sound sources.

…

Press

PHASE

to switch the P.CTL (Phase Control) ON

or OFF.

Note

• Phase matching is a very important factor in achieving proper

sound reproduction. If two waveforms are ‘in phase’, they

crest and trough together, resulting in increased amplitude,

clarity and presence of the sound signal. If a crest of a wave

meets a trough, then the sound will be ‘out of phase’ and an

unreliable sound image will be produced.

•

If your subwoofer has a phase control switch, set it to the

plus (+) sign (or 0°). However, the effect you can actually

feel when Phase Control is set to ON on this receiver

depends on the type of your subwoofer. Set your

subwoofer to maximize the effect. It is also recommended

you try changing the orientation or the place of your

subwoofer.

•

Set the built-in lowpass filter switch of your subwoofer to

OFF. If this cannot be done on your subwoofer, set the

cutoff frequency to a higher value.

•

If the speaker distance is not properly set, you may not

have a maximized Phase Control effect.

•

The Phase Control mode cannot be set to ON in the

following cases:

When the PURE DIRECT mode is switched on.

When the headphones are connected.

Setting the Audio options

There are a number of additional sound settings you can

make using the AV ADJUST menu. The defaults, if not

stated, are listed in bold.

Important

•

Note that if a setting doesn’t appear in the AV ADJUST

menu, it is unavailable due to the current source, settings

and status of the receiver.

Press

AV ADJUST

button.

Use





to select the setting you want to adjust.

Depending on the current status/mode of the receiver,

certain options may not be able to be selected. Check

the table below for notes on this.

Use





to set it as necessary.

See the table below for the options available for each

setting.

Press

RETURN

to confirm and exit the menu.

PHASEPHASE

S.RETRIEVER

BT AUDIO

BASS

USBTUN

AUX

ADJUST

MUTE

HOME

RETURNRETURN

VOLUME

Setting/What it does Option(s)

EQ (Acoustic Calibration EQ)

Switches on/off the effect of Acoustic

Calibration EQ.

OFF

S.DLY (Sound Delay)

Some monitors have a slight delay when

showing video, so the soundtrack will be

slightly out of sync with the picture. By adding

a bit of delay, you can adjust the sound to

match the presentation of the video.

0 ms to 500 ms

(1 step : 5 ms)

Default: 0

MIDNIGHT/LOUDNESS

The MIDNIGHT allows you to hear effective

surround sound of movies at low volumes.

The

LOUDNESS

is used to get good bass and

treble from music sources at low volumes.

M/L OFF

MIDNIGHT

LOUDNESS

S.RTV (Advanced Sound Retriever)

Switches on/off the effect of Advanced Sound

Retriever. (see Using the Advanced Sound

Retriever above)

OFF

DUAL MONO

Specifies how dual mono encoded Dolby

Digital soundtracks should be played.

CH1 – Channel 1

is heard only

CH2 – Channel 2

is heard only

CH1 CH2 – Both

channels heard

from front

speakers

Listening to your system

Using the Advanced Sound Retriever

When audio data is removed during the compression

process, sound quality often suffers from an uneven sound

image. The Advanced Sound Retriever feature employs new

DSP technology that helps bring CD quality sound back to

compressed 2-channel audio by restoring sound pressure

and smoothing jagged artifacts left over after compression.

…

Press

S.RETRIEVER

to switch the S.RTV (Advanced

Sound Retriever) ON or OFF.

Note

• The Advanced Sound Retriever mode cannot be set to

when the

DIRECT

mode or the

PURE DIRECT

mode is

switched on.

Better sound using Phase Control

This receiver’s Phase Control feature uses phase correction

measures to make sure your sound source arrives at the

listening position in phase, preventing unwanted distortion

and/or coloring of the sound.

Phase Control technology provides coherent sound

reproduction through the use of phase matching for an

optimal sound image at your listening position. The default

setting is on and we recommend leaving Phase Control

switched on for all sound sources.

…

Press

PHASE

to switch the P.CTL (Phase Control) ON

or OFF.

Note

• Phase matching is a very important factor in achieving proper

sound reproduction. If two waveforms are ‘in phase’, they

crest and trough together, resulting in increased amplitude,

clarity and presence of the sound signal. If a crest of a wave

meets a trough, then the sound will be ‘out of phase’ and an

unreliable sound image will be produced.

•

If your subwoofer has a phase control switch, set it to the

plus (+) sign (or 0°). However, the effect you can actually

feel when Phase Control is set to ON on this receiver

depends on the type of your subwoofer. Set your

subwoofer to maximize the effect. It is also recommended

you try changing the orientation or the place of your

subwoofer.

•

Set the built-in lowpass filter switch of your subwoofer to

OFF. If this cannot be done on your subwoofer, set the

cutoff frequency to a higher value.

•

If the speaker distance is not properly set, you may not

have a maximized Phase Control effect.

•

The Phase Control mode cannot be set to ON in the

following cases:

When the PURE DIRECT mode is switched on.

When the headphones are connected.

Setting the Audio options

There are a number of additional sound settings you can

make using the AV ADJUST menu. The defaults, if not

stated, are listed in bold.

Important

•

Note that if a setting doesn’t appear in the AV ADJUST

menu, it is unavailable due to the current source, settings

and status of the receiver.

Press

AV ADJUST

button.

Use





to select the setting you want to adjust.

Depending on the current status/mode of the receiver,

certain options may not be able to be selected. Check

the table below for notes on this.

Use





to set it as necessary.

See the table below for the options available for each

setting.

Press

RETURN

to confirm and exit the menu.

PHASEPHASE

S.RETRIEVER

BT AUDIO

BASS

USBTUN

AUX

ADJUST

MUTE

HOME

RETURNRETURN

VOLUME

Setting/What it does Option(s)

EQ (Acoustic Calibration EQ)

Switches on/off the effect of Acoustic

Calibration EQ.

OFF

S.DLY (Sound Delay)

Some monitors have a slight delay when

showing video, so the soundtrack will be

slightly out of sync with the picture. By adding

a bit of delay, you can adjust the sound to

match the presentation of the video.

0 ms to 500 ms

(1 step : 5 ms)

Default: 0

MIDNIGHT/LOUDNESS

The MIDNIGHT allows you to hear effective

surround sound of movies at low volumes.

The

LOUDNESS

is used to get good bass and

treble from music sources at low volumes.

M/L OFF

MIDNIGHT

LOUDNESS

S.RTV (Advanced Sound Retriever)

Switches on/off the effect of Advanced Sound

Retriever. (see Using the Advanced Sound

Retriever above)

OFF

DUAL MONO

Specifies how dual mono encoded Dolby

Digital soundtracks should be played.

CH1 – Channel 1

is heard only

CH2 – Channel 2

is heard only

CH1 CH2 – Both

channels heard

from front

speakers

Listening to your system

Using the Advanced Sound Retriever

When audio data is removed during the compression

process, sound quality often suffers from an uneven sound

image. The Advanced Sound Retriever feature employs new

DSP technology that helps bring CD quality sound back to

compressed 2-channel audio by restoring sound pressure

and smoothing jagged artifacts left over after compression.

…

Press

S.RETRIEVER

to switch the S.RTV (Advanced

Sound Retriever) ON or OFF.

Note

• The Advanced Sound Retriever mode cannot be set to

when the

DIRECT

mode or the

PURE DIRECT

mode is

switched on.

Better sound using Phase Control

This receiver’s Phase Control feature uses phase correction

measures to make sure your sound source arrives at the

listening position in phase, preventing unwanted distortion

and/or coloring of the sound.

Phase Control technology provides coherent sound

reproduction through the use of phase matching for an

optimal sound image at your listening position. The default

setting is on and we recommend leaving Phase Control

switched on for all sound sources.

…

Press

PHASE

to switch the P.CTL (Phase Control) ON

or OFF.

Note

• Phase matching is a very important factor in achieving proper

sound reproduction. If two waveforms are ‘in phase’, they

crest and trough together, resulting in increased amplitude,

clarity and presence of the sound signal. If a crest of a wave

meets a trough, then the sound will be ‘out of phase’ and an

unreliable sound image will be produced.

•

If your subwoofer has a phase control switch, set it to the

plus (+) sign (or 0°). However, the effect you can actually

feel when Phase Control is set to ON on this receiver

depends on the type of your subwoofer. Set your

subwoofer to maximize the effect. It is also recommended

you try changing the orientation or the place of your

subwoofer.

•

Set the built-in lowpass filter switch of your subwoofer to

OFF. If this cannot be done on your subwoofer, set the

cutoff frequency to a higher value.

•

If the speaker distance is not properly set, you may not

have a maximized Phase Control effect.

•

The Phase Control mode cannot be set to ON in the

following cases:

When the PURE DIRECT mode is switched on.

When the headphones are connected.

Setting the Audio options

There are a number of additional sound settings you can

make using the AV ADJUST menu. The defaults, if not

stated, are listed in bold.

Important

•

Note that if a setting doesn’t appear in the AV ADJUST

menu, it is unavailable due to the current source, settings

and status of the receiver.

Press

AV ADJUST

button.

Use





to select the setting you want to adjust.

Depending on the current status/mode of the receiver,

certain options may not be able to be selected. Check

the table below for notes on this.

Use





to set it as necessary.

See the table below for the options available for each

setting.

Press

RETURN

to confirm and exit the menu.

PHASEPHASE

S.RETRIEVER

BT AUDIO

BASS

USBTUN

AUX

ADJUST

MUTE

HOME

RETURNRETURN

VOLUME

Setting/What it does Option(s)

EQ (Acoustic Calibration EQ)

Switches on/off the effect of Acoustic

Calibration EQ.

OFF

S.DLY (Sound Delay)

Some monitors have a slight delay when

showing video, so the soundtrack will be

slightly out of sync with the picture. By adding

a bit of delay, you can adjust the sound to

match the presentation of the video.

0 ms to 500 ms

(1 step : 5 ms)

Default: 0

MIDNIGHT/LOUDNESS

The MIDNIGHT allows you to hear effective

surround sound of movies at low volumes.

The

LOUDNESS

is used to get good bass and

treble from music sources at low volumes.

M/L OFF

MIDNIGHT

LOUDNESS

S.RTV (Advanced Sound Retriever)

Switches on/off the effect of Advanced Sound

Retriever. (see Using the Advanced Sound

Retriever above)

OFF

DUAL MONO

Specifies how dual mono encoded Dolby

Digital soundtracks should be played.

CH1 – Channel 1

is heard only

CH2 – Channel 2

is heard only

CH1 CH2 – Both

channels heard

from front

speakers

Listening to your system

Using the Advanced Sound Retriever

When audio data is removed during the compression

process, sound quality often suffers from an uneven sound

image. The Advanced Sound Retriever feature employs new

DSP technology that helps bring CD quality sound back to

compressed 2-channel audio by restoring sound pressure

and smoothing jagged artifacts left over after compression.

…

Press

S.RETRIEVER

to switch the S.RTV (Advanced

Sound Retriever) ON or OFF.

Note

• The Advanced Sound Retriever mode cannot be set to

when the

DIRECT

mode or the

PURE DIRECT

mode is

switched on.

Better sound using Phase Control

This receiver’s Phase Control feature uses phase correction

measures to make sure your sound source arrives at the

listening position in phase, preventing unwanted distortion

and/or coloring of the sound.

Phase Control technology provides coherent sound

reproduction through the use of phase matching for an

optimal sound image at your listening position. The default

setting is on and we recommend leaving Phase Control

switched on for all sound sources.

…

Press

PHASE

to switch the P.CTL (Phase Control) ON

or OFF.

Note

• Phase matching is a very important factor in achieving proper

sound reproduction. If two waveforms are ‘in phase’, they

crest and trough together, resulting in increased amplitude,

clarity and presence of the sound signal. If a crest of a wave

meets a trough, then the sound will be ‘out of phase’ and an

unreliable sound image will be produced.

•

If your subwoofer has a phase control switch, set it to the

plus (+) sign (or 0°). However, the effect you can actually

feel when Phase Control is set to ON on this receiver

depends on the type of your subwoofer. Set your

subwoofer to maximize the effect. It is also recommended

you try changing the orientation or the place of your

subwoofer.

•

Set the built-in lowpass filter switch of your subwoofer to

OFF. If this cannot be done on your subwoofer, set the

cutoff frequency to a higher value.

•

If the speaker distance is not properly set, you may not

have a maximized Phase Control effect.

•

The Phase Control mode cannot be set to ON in the

following cases:

When the PURE DIRECT mode is switched on.

When the headphones are connected.

Setting the Audio options

There are a number of additional sound settings you can

make using the AV ADJUST menu. The defaults, if not

stated, are listed in bold.

Important

•

Note that if a setting doesn’t appear in the AV ADJUST

menu, it is unavailable due to the current source, settings

and status of the receiver.

Press

AV ADJUST

button.

Use





to select the setting you want to adjust.

Depending on the current status/mode of the receiver,

certain options may not be able to be selected. Check

the table below for notes on this.

Use





to set it as necessary.

See the table below for the options available for each

setting.

Press

RETURN

to confirm and exit the menu.

PHASEPHASE

S.RETRIEVER

BT AUDIO

BASS

USBTUN

AUX

ADJUST

MUTE

HOME

RETURNRETURN

VOLUME

Setting/What it does Option(s)

EQ (Acoustic Calibration EQ)

Switches on/off the effect of Acoustic

Calibration EQ.

OFF

S.DLY (Sound Delay)

Some monitors have a slight delay when

showing video, so the soundtrack will be

slightly out of sync with the picture. By adding

a bit of delay, you can adjust the sound to

match the presentation of the video.

0 ms to 500 ms

(1 step : 5 ms)

Default: 0

MIDNIGHT/LOUDNESS

The MIDNIGHT allows you to hear effective

surround sound of movies at low volumes.

The

LOUDNESS

is used to get good bass and

treble from music sources at low volumes.

M/L OFF

MIDNIGHT

LOUDNESS

S.RTV (Advanced Sound Retriever)

Switches on/off the effect of Advanced Sound

Retriever. (see Using the Advanced Sound

Retriever above)

OFF

DUAL MONO

Specifies how dual mono encoded Dolby

Digital soundtracks should be played.

CH1 – Channel 1

is heard only

CH2 – Channel 2

is heard only

CH1 CH2 – Both

channels heard

from front

speakers

Advanced Sound Retrieverin käyttö

Kun kompression yhteydessä poistetaan audiodataa,

äänenlaatu kärsii ja äänikuva on epätasainen.

Advanced Sound Retriever-toiminto hyödyntää uutta

DSP-teknologiaa ja palauttaa CD-tason äänenlaatua

kompressoituun kaksikanavaiseen audioon

muokkaamalla sen dynamiikkaa alkuperäisen kaltaiseksi

ja tasoittamalla kompression aiheuttamia vääristymiä.

Paina

S.RETRIEVER

, joka kytkee Advanced Sound

Retrieverin päälle ja pois.

Huomio

• Advanced Sound Retrieveriä ei voi käyttää, kun

kuuntelutilana on DIRECT tai PURE DIRECT.

Parempi ääni Phase Controlilla

Vastaanottimen Phase Control -toiminto tekee

vaihekorjauksen ja varmistaa, että äänet kuuluvat

kuuntelukohtaan samassa vaiheessa. Näin estetään

tarpeetonta säröytymistä ja/tai äänen värittymistä.

Phase Control -teknologia antaa tasaisen äänentoiston

sovittamalla äänikuvan vaiheet optimaalisesti

kuuntelukohtaan. Oletusarvona ominaisuus on päällä

ja suosittelemme Phase Controlin käyttöä kaikille

äänilähteille.

Paina

PHASE

, jokä kytkee P.CTL:n (Phase Control)

päälle ja pois.

Huomio

• Vaiheistuksen sovitus on tärkeä osa laadukasta

äänentoistoa. Jos kaksi ääniaaltoa ovat samassa

vaiheessa, ne vahvistavat, selkeyttävät ja täsmentävät

toisiaan. Jos taas ääniaallot ovat vastavaiheisia,

aiheutuu vaihevirhe ja äänikuva on epävakaa.

• Jos alataajuuskaiuttimessasi on vaihekytkin, aseta

siihen plus (+) (tai 0°). Tämän vastaanottimen

Phase Controlin vaikutuksen tuntuvuus riippuu

alataajuuskaiuttimesta. Säädä alataajuuskaiutin

vaikutuksen maksimoimiseksi. Voit myös kokeilla

alataajuuskaiuttimen paikkaa tai suuntausta.

• Aseta alataajuuskaiuttimesi sisäinen alipäästösuodin

pois päältä. Jos tätä ei voi tehdä, säädä päästötaajuus

ylempään arvoon.

• Jos kaiuttimien etäisyyksien asetuksia ei ole tehty

oikein, Phase Control-efekti ei ole parhaimmillaan.

• Phase Control-tilaa ei voi valita seuraavissa

tapauksissa:

- Kuuntelutilana on PURE DIRECT.

- Kuulokkeet on kytketty.

Audion asetuksien valitseminen

AV ADJUST -valikosta voit tehdä lukuisia lisäasetuksia

äänelle. Oletusarvot on esitetty lihavoituna.

Tärkeä

• Mikäli asetus ei näy AV ADJUST -valikossa, sitä ei voi

valita johtuen äänilähteestä tai vastaanottimen tilasta ja

asetuksista.

1 Paina näppäintä

AV ADJUST

2 Valitse säädettävä asetus näppäimillä .

3 Tee säädöt näppäimillä tarpeen mukaan.

4 Vahvista asetukset painamalla

RETURN

ja poistut

valikosta.

Asetus/Mitä se tekee Optiot

Kytkee akustisen kalibraation

ekvalisaattorin päälle/pois.

Joissakin näytöissä on viive videossa

ja ääniraita ei ole synkronisoitu kuvan

kanssa. Lisäämällä viivettä voit

sovittaa äänen vastaamaan kuvaa.

0 ms–500 ms

(askel: 5 ms)

Oletus: 0

MIDNIGHT mahdollistaa elokuvien

surround äänen tehollisen kuuntelun

hiljaisella voimakkuudella.

LOUDNESS antaa hyvän basson ja

diskantin musiikin hiljaisessa kuuntelussa.

Kytkee Advanced Sound Retriever-efektin

päälle ja pois (katso ylempää: Advanced

Sound Retrieverin käyttö).

Määrittelee dual mono -koodattujen

Dolby Digital -ääniraitojen soittamisen.

CH1 – Vain

kanava 1 kuuluu

CH2 – Vain

kanava 2 kuuluu

CH1 CH2

– Molemmat

kanavat kuuluvat

etukaiuttimista

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-531D in the language / languages: Finnish as an attachment in your email.

The manual is 10,27 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSX-531D

Pioneer VSX-531D User Manual - English - 41 pages

Pioneer VSX-531D User Manual - German - 41 pages

Pioneer VSX-531D User Manual - Dutch - 41 pages

Pioneer VSX-531D User Manual - French - 41 pages

Pioneer VSX-531D User Manual - Italian - 41 pages

Pioneer VSX-531D User Manual - Spanish - 41 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pioneer VSX-531D Manual

Product: