455215
83
Zoom out
Zoom in
Previous page
1/100
Next page
Additional information
13
83
En
Video
Settings
Symptom Remedy
No image is output when an
input is selected.
• Check the video connections of the source component (see page 18).
• For high-definition video (using component video connections), or when digital video conversion
is switched off (in Setting the Video options on page 72), you must connect your TV to this receiver
using the same type of video cable as you used to connect your video component.
• Make sure the input assignment is correct for components connected using component or HDMI
cables (see The Input Setup menu on page 67).
• Check the video output settings of the source component.
• Check that the video input you selected on your TV is correct.
• Some components (such as video game units) have resolutions that may not be converted. If
adjusting this receiver’s Resolution setting (in Setting the Video options on page 72) and/or the
resolution settings on your component or display doesn’t work, try switching Digital Video
Conversion (in Setting the Video options on page 72) OFF.
Can’t record video. • Check that the source is not copy-protected.
• The video converter is not available when making recordings. Check that the same type of video
cable is used for connecting both the recorder and the video source (the one you want to record) to
this receiver.
Noisy, intermittent, or distorted
picture.
• Sometimes a video deck may output a noisy video signal (during scanning, for example), or the
video quality may just be poor (with some video game units, for example). The picture quality may
also depend on the settings, etc. of your display device. Switch off the video converter and reconnect
the source and display device using the same type of connection (component or composite), then
start playback again.
Symptom Remedy
The Auto MCACC Setup
continually shows an error.
• The ambient noise level may be too high. Keep the noise level in the room as low as possible (see
also Problems when using the Auto MCACC Setup on page 11). If the noise level cannot be kept low
enough, you will have to set up the surround sound manually (page 41).
After using the Auto MCACC
Setup, the speaker size setting
is incorrect.
• There may have been some low frequency noise in the room from an air-conditioner, motor, etc.
Switch off all other appliances in the room and use Auto MCACC Setup again.
• Depending on a number of factors (room size, speaker placement, etc.) this may occur in some
cases. Change the speaker setting manually in Speaker Setting on page 48, and use the ALL (Keep
SP System) option for the Custom Menu in Automatic MCACC (Expert) on page 38 if this is a
recurring problem.
Can’t adjust the Fine Speaker
Distance setting (page 42)
properly.
• Check that the speakers are all in phase (make sure the positive (+) and negative () terminals are
matched up properly).
The display shows KEY LOCK
ON when you try to make
settings.
• With the receiver in standby, press STANDBY/ON while holding down the SPEAKERS button to
disable the key lock.
Most recent settings have been
erased.
• The power cord was disconnected from the wall while adjusting this setting.
VSX-1018AH_KU.book Page 83 Monday, March 10, 2008 4:51 PM
83


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-1018AH-K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-1018AH-K in the language / languages: English as an attachment in your email.

The manual is 3,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSX-1018AH-K

Pioneer VSX-1018AH-K User Manual - English - 37 pages

Pioneer VSX-1018AH-K User Manual - German - 96 pages

Pioneer VSX-1018AH-K User Manual - German - 37 pages

Pioneer VSX-1018AH-K User Manual - Dutch - 37 pages

Pioneer VSX-1018AH-K User Manual - Dutch - 96 pages

Pioneer VSX-1018AH-K User Manual - French - 96 pages

Pioneer VSX-1018AH-K User Manual - French - 37 pages

Pioneer VSX-1018AH-K User Manual - Italian - 96 pages

Pioneer VSX-1018AH-K User Manual - Italian - 37 pages

Pioneer VSX-1018AH-K User Manual - Swedish - 186 pages

Pioneer VSX-1018AH-K User Manual - Spanish - 96 pages

Pioneer VSX-1018AH-K User Manual - Spanish - 37 pages

Pioneer VSX-1018AH-K User Manual - Norwegian - 186 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info